Archived
Forum Replies Created
-
Hope this helps…This is what fits my Nov. 2005 date of manufacture Series 60
-
Hello, Bill. I have an 8V92 and keep a spare engine belt that I purchased at NAPA. It is a Gates Hi-Power IIPowerBand A92. It is a single triple rib belt. Hope this helps.
I will post a picture for you as soon as I can.
R
-
We have used the Escapees mail service for years. They have handled every request correctly. Most of our bills are paid via our credit union so very few bills are forwarded.
You can choose the frequency of service, we use once per week.
Sure works well for us as we are full timers.
-
There are always inconsiderate morons among us. Your guy Davy may have been deliberately delaying you thinking you’re a rich bus owner and not in his league.
-
I think you have a jake so my response may not be correct. My retarder equipped transmission has an intercooler which is a heat exchanger that circulates coolant around transmission fluid lines. In a previous vintage it was a cylinder shape about 8″ in diameter and 18″ long, and in the case of my current coach it is a box shape about 4 X 8 X 18″ long. Both were located on the lower driver side near the front of the engine oil pan. I don’t know how an H is configured in that area so I don’t know if you have any baffling that blocks your view of it.
Your transmission with a jake tracks engine temp closely most of the time, but with a retarder the transmission temp goes up and down over a relatively wide range depending on how hard the retarder is working.
-
A similar story from a few weeks ago. I pull into a truck stop around Athens, TN for fuel. All lanes were in use with another rig waiting. There was one free lane with a truck parked out in front who had finished fueling and pulled forward, so I of course chose that one. I fuel up as normal taking about 110 gallons so it takes a bit of time during which the rig in front of me is still sitting there. I finish and wait, and wait, getting more and more irritated. There is no one waiting behind me at this point so I consider unhooking my tow vehicle, but since I pulled straight in decide to try and back out. By inching back, staying in a complete straight line and watching the tow bar alignment in the rear view camera, I was able to back 40′ or so and exit through the CAT scales. Dude’s truck was still sitting there as a drove by on the way out. I guess he was still inside taking a shower.
-
I was only suggesting conversion type parking to allow side by side comparison of one coach to another. I know the Royale have a lot of similarities but a lot of changes over the years before ceasing production. Just think it would be great to look at them in close proximity.
I notice a lot of conservation among conversion types talking about their bus and others relating mine is not that way.
-
We checked into a campground in California a couple hours ago on our way to Indio and had no problems.
-
1. There is a device that connects to the plug that is used to calibrate system only Marathon would have this as this was their MDM data management system pre Techlon.
-
My clue was my fingers and hands. Part of my pre-trip or 5000 mile service is to run my hands around the tire treads. Apart from looking for cuts or stuff stuck in the tire, I am feeling the treads and it is incredible how the slightest uneven wear can be sensed by your fingers and hands.
Normally there is no indication of any unusual wear, visually or be touch, but in my case I could feel the wear was unusual compared to other axles and when I looked very close I could see some feathering on the tread.
If it is bad enough to feel bad, like poor tracking, or wandering, or pulling to one side you really, really need an alignment.
-
Every body recovered except those that died.
-
Thanks Don.
This was new to me as I had missed the old conversations about this issue. It did not happen during the first 5 years of owning the bus so clearly I have “sprung” an aux leak that is likely the culprit.
I am going to check into leaks over the next couple days which i should do either way, then I’ll start to look into SB-9614B and see about kit availability and if anyone is doing them (I can’t or don’t get under the bus so nothing I can do) these days.
We do raise the tags to improve our turning radius so ideally I can just eliminate it either via leak prevention or the SB.
Nobody raised it, but I assume that in the meantime having it sit on the Drives after the tags release (it does not lean BTW) is not going to cause other issues.
Always learning….
-
Thanks, guys. Just trying to figure out which boxes to check on the forms. The line for “Cash Advance” is the only one highlighted, so I don’t know if that’s what they want me to select. I hope not. I’ll email Gina today.
-
Do what Joe Carter said, or do Prevost SB96-14B
Up through 1996-1997 the plumbing of the tag axle lift circuit required that there be sufficient air pressure in the auxilary air tank air sytem to properly pilot the valves associated with the tag axle and tag lift system. Thus you needed good aux. air pressure to keep the coach at normal ride height in the rear of the vehicle. Lack of proper air through an air leak would eventually reduce pilot or control port air pressure to the point where the internal spring tension of the valve overcame the control pressure and the system cycled much the same as if you had flipped the tag lift lever. The difference being that there is no aux air pressure left to do anything with the system.
Engineering at Prevost redid the pneumatic “plumbing” of this circuit in 1997 so that there were no control pressures to any of these valves to keep the tag axle down and the tag lift circuits off. There was a maintenance bulletin released “Service Bulletin 96-14B) to increase the reliability of the pneumatic system. The bulletin can be found at
https://secure5.volvo.com/technicalpublications/pdf/Sb96-14B.pdf
There were various kits made at the time for different models. These would come with instructions and valves that had the proper brass fitting for the application. The kits also included an inversion valve that had to be plumbed into the circuit. Prevost has always cancelled the brake boosters on the tag axle when it was lifted to prevent tire damage. As we were changing the way the axle was controlled we had to change the control of the Bendix R12 valves that controlled whether there would be brake application pressure sent to the boosters on the tag axle or not.
The modification takes some time as the old valves need to be removed and air lines properly identified. Then the new valve installed correctly and the inversion valve installed. Plus the light circuit in the dash had to be changed to reflect the lack of air pressure in the controls when the vehicle was in the normal ride height position.
All that being said: to check your system! Run vehicle and get all air tanks filled. Turn off coach. Open accessory (auxilary) air tank and bleed down the pressure. If the coach has the newer system installed the vehicle should NOT settle in the rear as if you flipped the tag lift lever. If if does squat, then it most likely did not have this modification done.
-
When the Aux tank pressure drops and the tag “interlock” Norgren valve losses it’s pilot air pressure, the Norgren spring moves the shuttle to isolate the drive air bags and vent the tag bags. The problem with this is there are two Norgren valves and so the right and left side will vent slightly differently resulting in the coach going out of level – if parked and not on the air bag stops.
I plugged the vents on these 2 Norgrens. Now that means I can not raise the tag. But I never raised the tag anyways.