Archived
Forum Replies Created
-
Looking at the top control, mine is for the rear camera with the ability to aim the view Down on the toad or Up for farther back down the road. I also have the rear camera linked to the dash iPad so you need to make sure the top button is On.
As far as I know, my side cameras are set in one position only and come on as you hit the directional signal.
-
When I had an engine swapped out in my old ’88 coach by American Fleet in Springfield, MO (the best engine folks I know) the last thing they said to me was never leave the coach at idle. Turn it off or get it to high idle for any extended period.
I also discovered the “let it idle for 2 minutes in cold weather” problem. We were getting ready to leave MI and did not wait until I say 90 PSI on the air tanks and flipped it to high idle anyway. Went back to check the engine before leaving and found the engine fan belt had jumped off as the air bag had not yet inflated.
Won’t make that mistake again.
-
It controls the side & rear cameras.
-
I seriously doubt we have measurable turbo boost while idling, but if we do, so what?
A turbo is well lubricated and at low RPMs such as low or high idle it is merely loafing along with ample oil pressure keeping the bearings well lubricated.
-
What Mark said. Many moons ago when the 8V92 was the standard motor home engine Prevost (at a seminar) said to never idle for long periods at low idle speed. The engine will not heat properly, the oil pressure is low, and the alternator output is minimal.
At high idle you will not drain the battery, even with OTR, the engine will heat and retain the heat, and there will be ample oil pressure.
As a practical matter we should not be idling our engines for extended periods, but if we have to use the high RPM. Unless it is essential to idle the engine such as in sub zero temps when a restart might be an issue shut it down, and use the generator if required.
What does the operator or driver’s manual say about idling? I went through my operator’s manual and it mentioned fast idle only twice. Once it mentioned to engage it during slide operation and the second mention was after a cold engine start and 2 minutes of slow idle to go to fast idle. There was no other mention of how and when to use it.
-
I think that is total BS. Detroit used to say to never let it idle unless at a higher speed. Think about it…140 is not operating temp. In colder temp regions it would not probably even get that high. You likely have EGR on your engine. Without getting up operating temps, or as close as you can get it, you are likely not burning fuel efficiently and could be creating more gunk in your valve train and in the piston ring area. Even with high idle, we used to see issues in the winter with unburned fuel slobbering out of the exhaust after drivers would take a sleep break. That was WITH high idle on. We had to turn it up about 300 RRPM on some units to get rid of that problem.
You also do not have as much oil pressure, and depending on the electrical load, not getting the amps you would at a higher RPM. I can not think of any time I left my coaches at low idle for any amount of time. Unless cooling it down at the end of a trip I always flipped the high idle switch.
I wonder if the real reason it is not to keep noise levels down due to some local issues….??
-
Jon,
That’s exactly what I was looking for and found it. It’s second bay back on the passenger side behind a little panel. Three fusses and three relays. Found it fixed it, it’s the finding part that wares you out. Makes no sense generator and fans are on driver side but power and control on passenger side.
-
THANK YOU Jon
-
Hi and thanks so much for the feedback.
I like digital and would prefer to go that route, but reading the specs on the link that you sent specifically states not to use the gauges on Modified Sine Wave current, which is what we have.
The rig has 2 Heart Freedom Interface 24v 2800 EMS modified sine wave inverters.
I’d be interested in learning about digital gauges that can handle modified sine unless I win the lotto and then replace both inverters with Pure Sine 🙂
I apologize that I didn’t state my rationale for analog; Digital would be awesome but web searching hasn’t found any that state that they are good w/ Modified Sine, and I haven’t had time to call around….chasing leaks, ‘ya know.
Thanks again – perhaps one of the other gurus who hang out in these parts may have suggestions?
John
-
Archived
MemberJanuary 21, 2021 at 2:38 pm in reply to: “Best / Most Protective” Engine Oil Filter?I do not believe you are overthinking it, but you may be trying to make a choice with insufficient information.
I have almost exclusively used Baldwin B495, on a few occasions Donelson, once or twice NAPA, but I never cut open a filter, and I never deviated from my 5000 mile oil changes. But I have opened up my engine via the valve cover and oil pan and unlike my straight 40 weight 8V92 engine there was not a teaspoon of gray sludge in my engines.
How much my filters contributed to that cleanliness is unknown because on the 8V92 I used the Baldwin B95 almost exclusively but that engine had some gray sludge.
As to wear I have no clue. If the filters were inadequate, ample or overkill I have no clue. If Detroit is OK with my filter choice, so am I. And I do not know if they are OK with it.
-
Yea that’s the problem I’m having both are stuck in. I hope it releases now with the power unplugged like you suggested.
-
Davis Instruments, Vantage pro 11 wind cups, drill out mounting hole for proper fit. $120 each