Forum Replies Created

Page 72 of 2304
  • Archived

    Member
    April 6, 2021 at 9:22 am in reply to: Bay Door Damaged

    Not laughing at you Jon , sorry if it sounded that way . No doubt you are a man of many talents. I think in the end this will be another product that becomes cheaper to replace than repair . For me that is . I have a call in for a used door so i should know soon . I did send the pictures to Dick so maybe he can post them for me .

  • Archived

    Member
    April 5, 2021 at 10:10 pm in reply to: Fiber optic lighting

    Nice glad you where able to get it going. Where did you find the parts?

  • Archived

    Member
    April 5, 2021 at 7:28 pm in reply to: Damn that Tom

    There is nothing inside the bay, it’s just a cable pass thru.

    The dipole and ‘external’ antenna are clearly different. Jeff’s install looks like a lot of potential for cable snag which I was trying to avoid by dropping straight out of the bay.

    I’ll cut back a little of the silicone and see it it makes a difference. If not I’ll try the external antenna.

  • Archived

    Member
    April 5, 2021 at 6:54 pm in reply to: Damn that Tom

    Joe,

    I’m not clear on what you installed in the bay. The extended antenna requires a good ground and covering all but the tip in silicone could be your problem. I think the entire rubber ducky needs to be exposed. Like I said, I tried mounting under the steering bay with no success.

    Here’s one Jeff did.

  • Archived

    Member
    April 5, 2021 at 5:31 pm in reply to: A Door Lock Question

    Glad you got it fixed.

  • Archived

    Member
    April 5, 2021 at 5:20 pm in reply to: Bay Door Damaged

    Al, in times past at a rally a former tin knocker like myself took one of Mango Mikes damaged rub rails, hammered out the dents as good as possible, and then went on to demonstrate the multiple steps to restore a mirror polish.

    You may laugh, but guys who routinely do similar repairs can demonstrate methods to restore some bent metal to original condition.

    I was not a hands on metal guy, but I watched over a 40 year span how guys in my companies or the companies I worked at could fix damaged metal and make it look so easy a cave man could do it. I remember a very expensive stainless steel counter top that was 16 feet long, was completed and it got a belly in it from the man belt sanding it to make a brushed finish. He hesitated in one spot and the heat created the defect. It was for a hospital.

    The choice was to start all over and remake it or repair it. One of our highly skilled welders said he would fix it. He used a cut off saw in a die grinder to cut a slit right across the depression in the counter top and then used TIG welding to close the slit. The welding had the effect of shrinking the width of the slit that pulled the depression right out of the counter top.

    It was later belt sanded to provide the needed finish and it was as flat as could be. My point is things that appear difficult often have simple solutions.

  • Archived

    Member
    April 5, 2021 at 4:52 pm in reply to: A Door Lock Question

    I finally got it. Thanks to Joe and all the others that helped.

    I loosened each of the two small Philip head screws 10 1/4 turns each.

    Then I was able to remove the lock cylinder. I counted the turns as instructed and mine was out after five turns.

    I took it to a locksmith about 20 minutes from here in Centerville, Ohio. After looking it over, she surmised it had about 20 years of gunk in it. (Actually 26 years and nearly 400,000 miles of gunk)

    She cleaned it, re-keyed it to match the key for the lock on my other door and made five keys in about 40 minutes. She charged me $12 for the lock work and I about passed out. I gave her extra.

    (Please remember that the largest locksmith in our area asked for pictures of everything. Once he had time to study the pictures and part numbers I provided, he said it could not be re-keyed and it would be $600 for parts and labor. I knew he did not have a clue and lost his number.)

    I came home, installed the cylinder (I am so glad you told me to count the turns) and put it all back together.

    This piece of angle goes between the inside part of the lock and the door as a spacer.

    This is what it looks like from the inside.

    When I took it apart, it had pipe dope or something around it. Maybe to protect against a leak from the outside?

    Should I duplicate or leave as is?

    Thanks again.

    Davy

  • Archived

    Member
    April 5, 2021 at 4:36 pm in reply to: Damn that Tom

    Doesn’t look like the photos uploaded from the iPad

  • Archived

    Member
    April 5, 2021 at 12:52 pm in reply to: Michelin Tire Problems

    Hi everyone,

    I thought I’d chime in here, I’m the Pat/Michelin lady that Jon referred to above.

    Chuck, I have been in touch with our Florida Field Engineer and he is in an all day meeting today, but he lives in the Tampa area, so we can get some on-site technical resolution. Your tires haven’t been driven on for thousands of miles, so we should be able to understand the root cause analysis for your ride issues.

    If you can send your contact information over to me, we can get the tires rolling again, smoothly.

    My email is pat.meisenholder@michelin.com.

    NOTE- corrected my email above. Pat

  • Archived

    Member
    April 5, 2021 at 7:16 am in reply to: Damn that Tom

    I do want to get this straightened out, since doing a pre trip check and turning off the app loses a bit of the usefulness of the system.

    but to be clear my antenna is now external. I bought an SMA cable extension cable. The blue tooth receiver is in the overhead of my galley where it has a clear shot to the phone on the post my the driver. Any further back and the Bluetooth signal is lost.

    the antenna is then routed the bay in front of the drive wheels and the dipole is snug to the foam installation.

    Not sure where I would go with a different mounting option.

    I’ll try and send some pics later. for now it off to Stay Wars.

  • Archived

    Member
    April 5, 2021 at 6:52 am in reply to: Recommendations for RV Campgrounds in Phoenix area

    45 minutes down I 10 at Casa Grande and there’s Palm Creek Golf and RV Resort stayed there five winters, nice place.

  • Archived

    Member
    April 5, 2021 at 6:47 am in reply to: Zero out coach requirements

    The only thing I haven’t done out of the three post above is to coat my roof.

    My bus goes a lot faster now because my wallet is so much lighter LOL

    Chuck

  • Archived

    Member
    April 4, 2021 at 8:31 pm in reply to: Separation between Chuch and State

    No getting under the bus.

    Air Brake System Check
    For air brake equipped vehicles, the proper procedures for inspecting the air brake system are as follows:

    Test Air Leakage Rate (Static check)
    With a fully-charged air system, typically at 120 psi, turn the engine off, chock the wheels, release (push in) the parking brake button and trailer air supply button (for combination vehicles) and time the air pressure drop. After the initial drop, the rate of pressure loss should not be more than 2 psi per minute for single vehicles and no more than 3 psi per minute for combination vehicles.

    Test Air Brake System for Leaks
    Release (push in) the parking brake and trailer air supply button (for combination vehicles), and apply pressure to the foot brake. After the initial drop in pressure, the rate of pressure loss should be no more than 3 psi per minute for single vehicles and no more than 4 psi per minute for combination vehicles.

    Test Low Pressure Warning Alarm and/or Signal
    Turn the key to the on position. Rapidly depress and release the foot brake to reduce air tank pressure. The low air pressure warning signal must come on before the pressure drops below 60 psi.

    Check that the Spring Brakes Activate Automatically
    Continue to rapidly apply and release the service brake pedal further reducing air pressure. The trailer air supply button (for combination vehicles) and parking brake button should pop out when the pressure falls to usually between 20 to 40 psi. This should activate the spring brakes.

    Check Rate of Air Pressure Buildup
    While the engine is operating at 1800 RPM, the pressure should rise from 85 to 100 psi within 45 seconds in dual air systems.

    Test Foot (Service) Brakes
    With normal air pressure, release the parking brake and trailer air supply button (for combination vehicles), move the vehicle forward slowly at about 5 mph and apply the brakes firmly using the brake pedal. Test for any pulling to any one side or delayed stopping action.

  • Archived

    Member
    April 4, 2021 at 8:24 pm in reply to: Damn that Tom

    What type of monitor are you using?

  • Archived

    Member
    April 4, 2021 at 6:25 pm in reply to: Damn that Tom

    Tom gets to pick the next location for the dipole antenna. I’m on my third pick and the unit keeps losing communication with one of the sensors. I have tried:

    • the top front passenger corner of the wind shield and it drops the driver tag.
    • Inside the bay just ahead of the drive tires middle bus width, it drops the driver front sensor.
    • it is currently mounted below the floor of the bay just ahead of the drive tires about 1/3 way across the width of the bus, and it drops the front drivers side sensor.

    come on man, does it have to be in the exact center of the bus to work.

    as to the App when it goes into alarm, why does it just flash a notification, why not show the diagram and flash the offending tire in red.

    The bottom line is that it has lost communication so much I use it to check the tire pressures -pretrip and close the app. I checked them at our lunch stop but failed to close the app. It is so sensitive to position that rolling down the road it works, stopped in traffic or at the end of the day the driver front gets dropped and I never saw the notification on the phone. The phone is mounted on the drivers side column.

    My Hearing is fine. Phone Vibration is turned off, eyes not so good to read a notification.

    First time in nine years of owning the bus I’ve been stumped and called Prevost Pass. Bus hasn’t let me down yet. Haven’t used the bus enough, chalked it up to a good laugh.

Page 72 of 2304