Forum Replies Created

Page 47 of 2304
  • Archived

    Member
    September 26, 2021 at 8:39 pm in reply to: Cutting a corner too tight

    Art that’s an Eagle. Think it would just fly over.

  • Archived

    Member
    September 26, 2021 at 8:38 pm in reply to: Pre-Fab metal RV carport recommendation

    Location is key as freight cost is a big part.

  • Archived

    Member
    September 26, 2021 at 4:41 pm in reply to: Sitting on the dock of the bay…….

    Sometimes things Happen!

  • Archived

    Member
    September 25, 2021 at 7:05 pm in reply to: what did you do to your Bus Today

    Chuck: I am guilty of miss understanding ? from pump resivoil to supply side of pump just loosen hose and let the oil drain from res then replace hose (make sure it is oil rated) refill res then go..

  • Archived

    Member
    September 25, 2021 at 5:41 pm in reply to: what did you do to your Bus Today

    When BA was done did you give him a beer?

    Later

    bv

  • Archived

    Member
    September 25, 2021 at 4:01 pm in reply to: what did you do to your Bus Today

    Replaced the surge protector, it has been making a buzzing sound when connected too shore power. Was annoying when trying to go back to sleep after the 2 AM pee call.

    Larry and Miriam Nelson

    2002 XLII Vision

    2019 BUICK Envision

    Hurricane, UT

  • Archived

    Member
    September 25, 2021 at 1:33 pm in reply to: tire failure

    Nice to see you back A1.

    If that flat spot , losing 18/32 of thread in 6000 miles is normal wear I’ll buy a Liberty.

    Later

    bv

  • Archived

    Member
    September 24, 2021 at 7:43 pm in reply to: what did you do to your Bus Today

    Robert:

    I need to replace the supply line from the power steering pump tank to the power steering pump. When you removed yours to replace your pump did you have to do anything special to get the air back out of the power steering pump/lines?

    Chuck

  • Archived

    Member
    September 23, 2021 at 5:21 pm in reply to: shore power confusion

    I am not familiar with Marathon and their 120V AC electrical circuits, but I would bet serious money they did an excellent job balancing loads between L1 and L2.

    Without the benefit of actually knowing how your system has been modified the first thing I would do is verify when your device is measuring loads it is not seeing the same load twice. If your electrical panel ahead of the inverter electrical panel is the source of 120V AC power that feeds the inverter sub panel you want to be certain it is not also measuring the inverter sub panel loads. When there is shore or generator power available to the coach, the inverters receive that power as a pass through but when that shore or generator power is not available the inverter is creating that power from the coach house batteries.

    Your device is to limit current draw on shore power so you do not care what the current output is through the inverter sub panel. Keep in mind this is solely a guess and people who are more familiar with Marathon need to chime in and verify or refute this as a possible issue.

  • Archived

    Member
    September 23, 2021 at 3:57 pm in reply to: shore power confusion

    Check your 50 amp plug. Make sure you have 240 and not two 120 lines.

    i.e. measure Leg 1 to Leg 2, it should show 240. then measure Leg 1 to ground should show 120 and leg 2 to ground will show 120. If you don’t see 240 between L1 and L2 then you have a single 120 line split in 2.

    Don’t know where you are plugged in but some campgrounds will “cheat” and instead of 2 separate 120 lines they provide only 1 line and jump to both legs. Your watch dog will see all the current being pulled on one leg.

    To answer your question it depends on the converter. Some converters run all AC power from the transfer switch through the inverters, other don’t, Usually, L1 and L2 will go directly to the “MAIN” breaker panel and then from their run a 30 amp line, one from each leg to each inverter. then the output of the inverter runs to the smaller breaker box to power inverted circuits.

  • Archived

    Member
    September 23, 2021 at 12:52 am in reply to: Most miles seen.

    The guy from American Fleet (Brian, I think) that was a member here moved on a few years ago. I’m not sure that anyone else ever joined. They also moved to a different location in Springfield, MO.

  • Archived

    Member
    September 22, 2021 at 1:13 pm in reply to: Do H3 Rock back-and-forth more than an XLll

    Have been doing some research as We are thinking about our next coach and would figure, with same chassis and airbag situation/mounting, the extra height would sway a little more on the H3.

  • Archived

    Member
    September 21, 2021 at 12:18 pm in reply to: No oil pressure!!!

    Geeeesh Larry! When it rains it pours.

    I learned 45 years ago from some pretty savvy airplane mechanics that often the culprit can be a bad ground or a wire that has a failing crimp-on connector or ring-terminal. The bad ground can even be a little corrosion that is difficult to see, especially when a ring-terminal is difficult to get at. I was taught to “touch up” all the surfaces with a piece of emery cloth to make sure everything is shiny for a good connection.

    That training long ago has proved invaluable with the race cars and trailers.

  • Archived

    Member
    September 20, 2021 at 5:49 pm in reply to: No oil pressure!!!

    Was thinking of oil line from engine to gauge, and after posting remembered that vintage had electric signal from sensor.

  • Archived

    Member
    September 20, 2021 at 9:33 am in reply to: $9200 for a 20KVA Kohler rebuild

    Heat kills the Genny . My Vantare conversion locked the Genny in a tight box ” Bad Idea ” $20k later I’m back in business . New Genny head and rebuilt motor . I so fear heat I want to install a thermostat in the box to provide me temperature readings on the dash just in case the fan stops working . After 20k on a Genny you start thinking crazy .

Page 47 of 2304