Archived
Forum Replies Created
-
You all are starting to make me feel lazy!
When you run out of things on your buses… let me know 🙂
Bill
-
As I said, this is the first RV fourm I have ever seen it mentioned. That leaves A LOT of RVers with no idea that such a thing is even a thing.
-
BDuplan, Let me know how it goes and if you like the one you bought. I have been thinking about adding one of these to my tool arsenal.
-
Lost a long post when I clicked on POST and it said i had to be logged in. Long story short, in the 20+ years that I have been driving a Prevost I had never heard of a DOT brake check (as I suspect is true for every RVer driving coaches with air brakes).
We are now fixed but will return to Prevost to have them install some new air bags and some other issues the Houston Prevost folks apparently glanced over when we came in for a good going over after the purchase.
By the way, I have no history with any posters. Just differing opinions from a couple of us hard headed folks.
-
Open the engine compartment and read the label on right side of engine. It has a lot of specific info on your engine.
-
Today it was Country Coach ECC day. Some of you folks may have an older Country Coach like me, I had a few things that didn’t work like my Fog lights and my drivers side Docking lights. I have no CC schematics for my Bus, so I went thru each button inside the coach and identified every relay and device on each of these Boards. Well low and behold my Docking and Fog lights were on the Board with a Burned Ground Trace. See the pictures, I spliced in a wire, and Voila! I have Fog Lights and Drivers side docking lights. This was real easy to solder on, i just used a small piece of wire and jumpered across where the PCB trace was. I think Eventually if I keep the bus and have any issues, I am going to Replace this ECC with a Modern PLC.
-
Just finished replacing driver’s rear bags and rear 5 port leveling valves, replaced passengers rear bags last week. The passenger side had 1995 bags that were in amazingly good condition. The driver’s side drive axle had ’08 bags while the tag had a ’95 bag. I’m amazed at how durable the air bags are, to be 26 years old and minimal cracking. Tomorrow the front driver’s side windshield. My I’m having too much fun (not).
-
Archived
MemberSeptember 28, 2021 at 12:03 pm in reply to: Yanmar Diesel Service Marathon Generator Post 1Update:
Valve lash was per specification in Yanmar Maintenance Manual. Motor has 4000 hours on it now. This should have been done at 2000 hours.
The corrosion was caused by not flushing the cooling system and keeping up on SCA’s. The steel Yanmar freeze plugs on 1 and2 cylinders were extremely corroded.
The generator had no service records on it from previous two owners other then oil changes and belts. I had put this off until this year after purchase in 2018.
When we change the casting/freeze plugs we used brass….that turn out to be a problem. The brass plugs are very good but your installation technique has to be spot on. Steel is more forgiving. So we went back to the steel Yanmar casting plugs.
Drove to jobsite here in St Charles Louisanna and had generator temps 155 to 158 F.
Moral of story if you have a 20 year old generator and no history of critical maintenance. Be prepared to spend some money to
-
Here is the New Protector Boot installed
-
Thanks for asking, but no I couldn’t get into a good poker game and there were not any open caps tables!
I also didn’t go broke so it should only take a small loan to get out of service!
-
So, if someone would review the picture above, is there some kind of air regulator ahead of the brakes that would have a plastic part that looks like that? The wrecker driver might have said it was an air regulator that was leaking. Funny what pops into your head at 5:00 AM!
-
Okay, thanks for the info Dick!
Mike
-
WOW! I am a Big fan of the 4 square headlights.
-
I am wondering if the Brake test Jon is referring to would have caught this? Seems like he was underway when this happened. Reminder issues happen as we are driving also.