Archived
Forum Replies Created
-
A couple more things I will add when it comes to removal. #1, the night before spray with Kroil or PB Blaster or some penetrating lubricant. #2 the next day, just crack the bolts, then tighten, do this a few times to get the bolt moving so you don’t break it off. I used a 3/4″ Box wrench and mine loosened up no problem, no need for an impact. #3 After you have all the bolts moving, go ahead and remove all bolts/nuts except the top 2, I had one at 12:00 and one next to it. #4 wrap the straps and support the alternator weight. I put a board across the hole. #5 slowly remove the top two bolts and if you have the alternator supported correctly the back will be lifted up slightly pushing the Alt drive gear away from the cam gear. If you had studs like mine the studs will keep the alternator from falling down in the front, up to the point you slide it back off the studs. At this point the gears are apart and no damage to the Cam gear can happen. #6 Take a rag and place it in the hole to keep debris out. #7 Put a rag in the gear end of the alternator. #8 using the 2 straps, Lift it out.
-
From the top you can also do a nice job cleaning everything up. I had acorns, mouse dropping, stick, all kinds of stuff in between the Blower and the Valve cover running down both side. I used an air gun and blew out all the 30 years of accumulation.
-
I don’t see how it can be done from below. This access hatch makes it pretty easy. Bolts are right there, you can clean the area real good before you pull the alternator free, use the 2 strap method, I showed, as you will likely need to tilt one end or the other to pull it out. Stuff some rags in the gear drive end, and tape over the oil connection and there will be no mess. I moved the mattress out into the Galley and put cardboard down to place it once it comes out of the hole. Then put cardboard by yhe door so you can rest for going down the stairs. Once you get it up on the bed, two people can walk it out. From down below you can’t see if debris is falling into the Cam gear or if you are misaligned.
-
Hmmm. OK. Thanks guys. I will remove the carpet between the drawers and bed and see what i find.
-
I need to get at My Generator Radiator soon. I will post pics of how Country Coach did the install.
-
The Champ tips the scales at 105 lbs.
-
My Bed is east West also. I had 16.5″ and I got it done from the top.
-
Jerry, we had the same issue and ended up taking ours to Marathon in Dallas. They removed the storage areas above the house batteries and they were able to reach the radiator hoses from there. Very tight fit but was better than pulling generator.
-
Thanks for the data.
Your pinion is spinning slower than mine for a given mph. Your pinion rotates 3.58 revolutions to the ring gears (and drive tire) 1 revolution. Mine rotates 4.56 revolutions to the ring gears (and drive tire) 1 revolution.
If we’re both going 65 mph with the same diameter drive tire, your and my ring gears are turning at the same rpm. But my pinion is spinning faster than yours. -
Yea, your 1:1 in your final gear.
B500 is 1:1 in 4th. 5th & 6th or overdrive gears.
That’s why the difference in rear gear ratio.
-
Carguy….I’am thinking you have the record for most owned Prevost.
Just can’t make up your mind ?
AL
-
1400 RPM seems to ring a bell at 65? but I don’t remember, I will check for sure next time out. I have the 5 speed Close Ratio HT 755 CR Allison tranny.
-
Mike, It seems unlikely that they would use an accessory that may or may not be needed for the application as a path for critical engine lubrication. Just a hunch that i would not rely on.
I was in the pit yesterday trying to squeeze my body into the needed position to remove the 50dn. I may have to remove the cross member to get at the top bolts as i see no access from the bedroom.. It looks like it will be doable if things go ok. The photos and info in this thread have been very helpful to me. Thanks again.
-
Mike, when you are driving down the hwy at 65 mph, what is your rpm? Does your bus have a 5 or 6 speed Allison? Does it have a 2 speed differential?
Our bus runs down the hwy at 65 mph at 1550 rpm, if my memory serves me. Our Allison B500 6 speed is overdriven in 5th and 6th. It doesn’t have 2 speed differential.
If we had 3.58 gears in ours it lug the engine down, out of its sweet spot.
But, since your bus has a 8V92 etc, the sweet spot is different.
-
I don’t think the belt cover has saved any lives but I can confirm it does keep the grease off the engine.