Archived
Forum Replies Created
-
Hi Dick, See Below:
Where did you get the dimmer from?
Mike: Amazon, Here is the link:
https://www.amazon.com/gp/product/B01C4UBMY6/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&th=1
In the photo with the bird’s nest of wires, I see what looks like a the back of a rocker switch. Is that part of the install?
Mike: Those are actually lights also. They were illuminating the Country Coach emblem in the center of the Dash. I am not sure if they are Country coach installed or Prevost installed but they are all over the dash Panel to illuminate Brakes, or Tag Up, or Turn Signals. You can see more of them in the earlier pictures.
In the photo of the back of the gauge it appears the trapped a washer between the two plastic nuts and then glued the washer to the back of the gauge. Is that what you did?
Mike: The Led’s are a machined aluminum 11mm threaded body, with 2 aluminum lock nuts. I took both nuts off, and slipped a standard 7/16″ id washer and locked it against the underside of the LED flange with the 2 locknuts. Adding this washer in essence gave me a large mounting surface.
Did you use silicon or another adhesive?
Mike: I used a DAP product called DynaGrip 5X Max, but any construction adhesive will work. All of those square lights are held to the back of the dash panel with some kind of black semi flexible adhesive, so i didn’t feel bad using it in my application.
Did one of the plastic nuts fit in the kit hole in the back of the gauge?
Mike: Yes, all the holes were big enough except the Turbo Boost. I had to use a dremel and open the back up enough to drop the light in and bond it in place. As you can see in the Birds nest picture, the light sockets snap into the back sides of the gauges.
The bird’s nest picture I see three and four wires coming out of a fastener. What is that device called? Where can it be obtained.
Mike: I am not sure what you are talking about, Maybe the closed end crimp connectors?
-
Where did you get the dimmer from?
In the photo with the bird’s nest of wires, I see what looks like the back of a rocker switch. Is that part of the install?
In the photo of the back of the gauge it appears you trapped a washer between the two plastic nuts and then glued the washer to the back of the gauge. Is that what you did? Did you use silicon or another adhesive? Did one of the plastic nuts fit in the kit hole in the back of the gauge?
In the bird’s nest picture I see three and four wires coming out of a fastener. What is that device called? Where can it be obtained.
Great project. Great pictures! Thanks so much for sharing.
-
I replaced QR valve and treadle valve 4 years ago and it was there, I just rebuilt treadle valve and it is not there??
-
Update…
Thank you all for your suggestions, all good stuff…been busy all day until about 4pm…issue resolved thanks to Bernie that followed up with me and Marathon Service Dept at the Marathon HQ.
Again, Marathon Service Tech proved themselves as the best customer support in the coach conversions.
Electrical Tech Lead Terry took the time to guide me through troubleshooting and fixing the issue with patience and professionalism from start to finish.
THANK YOU!
Now to the issue at hand…as described in the initial post, I lost power to the coach completely, no inverters, no gen, nothing…
Through Marathon troubleshooting procedure, we were able to “resuscitate” the coach / inverters, get them to start charging the batteries and then root cause the issue…couple of the wires connected to the transfer switch breaker box were damaged / burned out, probably due to aging…replaced the two wires and we were back in business…coach all powered up and getting cooled…
Terry from Marathon Coach was “with me” the entire troubleshooting time making sure is done right the first time…
All forum suggestions were considered and in line with Marathon troubleshooting procedure.
Calling Jeff at Pelican was on my speed dial since 6am today, but wanted to give Marathon a chance…thank you!
THANK YOU Bernie and Terry at Marathon Coach, Coburn, Oregon…
Issue RESOLVED, thank you all!
Best regards,
Dorel
-
Big difference looks good ,nice job Mike
-
Ours has an electronic dump on both sides and the first thing I did was disable inside switches,,don’t know what they were thinking, could not imagine trying to get familiar with a new coach and dump in the middle of a campsite, not on our watch .
-
Thanks guys. Just nice knowing that I now have access when I need it.
-
Dick,
Depending on terrain and how bad you want to have the coach near the house have you considered a bus barn that never rises above the codes?
If you are allowed how about making half the height below ground? Assume the above ground height meets the code requirements, and make the additional needed height below ground. If needed place the bus door away from the street and to make it look normal from the street add windows or a person entry door properly placed relative to the ground level.
Obviously the driveway into the barn for the bus will be sloped down from ground level but assuming enough property that should not be an issue. A 55 foot long barn would be 21 feet wide, more than ample for the coach and a workshop.
-
And how exactly does OR enforce that law? I have a macerator and cannot even see it without a flashlight, and only then because I know where it is.
If OR had people write laws about banning macerators they should have gotten folks that had a clue. Entertainer conversions typically have tank drains on both sides with inside the coach controls. It is not uncommon to pull onto the shoulder where the slope is typically away from the road and with the push of a button the tank drains. If they park on the outside of a curve on the on or off ramp the view of them dumping is obscured. What they should have done to satisfy their concerns about illegal dumping is eliminate all inside the coach switches, and any outside switches should be near the tank drain so they get their shoes splashed if there is no hose attached.
-
Previous house we built was on a small lake had a large garage, all the neighbors kept asking what the big garage was for while the house was being built. We told them a submarine. Some neighbors actual took the bait. Had a lot of laughs over that.
Chuck
-
Thanks Mike and John for the info about the access panels. I Was able to peel the carpet back enough to see the panel and it appears to be like Mike’s. I will dig into it further over the weekend. Thanks again for taking so much time to provide so much detail.
-
Try a reboot on the inverter, Unplug coach from 12v turn off batteries, make sure inverter panel is off then turn on DC volts and then AC volts see what happens