Archived
Forum Replies Created
-
Thanks! I had a friend who was crew chief for one of the unlimited planes. After the accident his employer sold the plane. Didn’t get there while he was there. One of the things I’ve always wanted to see. I suspected the planes were a long ways away.
-
We have been there and we were pretty disappointed. Most of the time the planes are so far away you really can’t see what’s happening. It was fun to see some of the planes when they were parked but the race itself was pretty anti-climatic (IMHO).
I don’t know about parking on site as we were already in the area parked at a local casino campground.
-
I am not saying this is the case with the 1990 Marathon with the tire failure, but around that vintage and some later years Marathon exceeded the steer axle weight ratings. When I posted originally I had forgotten that. We have stressed often that tire pressures have to be based on the loads imposed and the only way to do that is to weight each axle at the least and at best each tire when the coach is fully loaded and has full fuel and water and an empty holding tank.
Proper tire pressures are extremely important and in the absence of a TPMS at every stop immediately check tire temps with an infrared temperature gun. If the pressures are correct for the weights they will be very close to one another. Shoot the hub temps also because a bad bearing or dragging brake can and will create serious problems.
-
Our best friend is our dog.The best human friend we have in this world may turn against us and become our enemy. Our son or daughter, we have reared with loving care, may prove ungrateful. Those who are nearest and dearest to us, those whom we trust with our happiness and our good name, may become traitors to the faith.The money that we have we may lose. It flies away from us, perhaps when we needs it most. Our reputation may be sacrificed in a moment of ill-considered action. The people who are prone to fall on their knees to do us honor when success is with us, may be the first to throw stones of malice when failure settles its cloud upon our heads. The one absolutely unselfish friend that we can have in this world, the one that never deserts us, and the one who never proves ungrateful or treacherous, is our dog.
Our dog stands by us in prosperity and in poverty, in health and in sickness. They will sleep on the cold ground, where the wintry wind blows and the snow drives fiercely, if only to be near our side. They will kiss the hand that has no food to offer. They will lick the wounds and sores that were caused by the roughness of the world. They guard the sleep of us, as if we’re a prince, even if we’re a pauper. When all other friends desert us, they remain. When riches takes wing and reputation falls to pieces, our dog is as constant in their love as the sun in its journey in the heavens. If fortune drives us forth as an outcast in the world, friendless and homeless, our faithful dog asks no higher privilege than that of accompanying us, to guard against danger, and to fight against enemies.When the last scene of all comes, and death takes us in its embrace and lay our body away in the cold ground, no matter if all other friends pursue their way, there by the graveside will be found our noble dog, their head between their paws, their eyes sad but open in alert watchfulness, faithful and true even to death.Author Unknown -
Archived
MemberMarch 14, 2022 at 2:33 pm in reply to: Transmission Temperature Dash Gauge Not WorkingHave you looked behind the dash to check the wiring? Maybe a bad or loose ground.
The trans and the engine have computers. I suspect that trans temp signal to the gauge probably comes from one of those computers.
Have you tried calling Prevost PASS: 800-463-7738. Operators are waiting to take your call now!
Joel wrote: “It’s a bit of a strain for me to get back to my earlier XL dash but are you sure it’s trans temp and not diff temp?” While the icon on the OEM gauge might be misleading, I’m pretty sure that gauge on our coach is “Trans Temp” because when I invoke the transmission retarder the temp climbs.
-
My plan is to remove the brake line on each canister, screw these in then put the brake line into this. I was going to leave the QR-1 in place for now.
-
Here is how I terminated all 18 LED Lights. I just used off the shelf terminal blocks I had lying around to make it easier. I also could have bundled them all together since they are such low Wattage.
-
Thanks Dick, I did try the Blue and the orange, for me, the cool white popped the best. I liked the Blue, but at full power it was not as bright as I would like. I will post a picture of my Terminal block setup later today.
-
Thanks for pointing us to the crimp connectors, especially what appear to be “the good ones”. I’ve been looking for them after seeing them in various devices but couldn’t find them!
Did you consider other colors of light? Test any?
You mention the wires went back to a terminal block. Is that existing behind the dash? or did you have to add that?
Great story and pictures! Thanks so much for sharing.
-
HI MIKE. not finding the sockets. can you post more to locate them please. thank you.
-
Our 2001 Marathon Locks the upper lock when we release the parking brake,
According to the Prevost wiring diagram there are two relays under the right hand dash, Relay two and Relay three. Excerpt from the wiring diagrams below.
RELAY 2 12.1 12V 562092 UNDER DASH R.H. UNLOCK ENTRANCE DOOR
RELAY 3 12.1 12V 562092 UNDER DASH R.H. ENTRANCE DOOR OPEN SIGNAL**** Prevost wiring diagram D060921 shows the Parking Brake Switch and the Door Air Lock Circuit.
***Link to Prevost wiring diagrams below.***
-
WoW big improvement! Good work Mike!
-
Dick-
I’m with you on wanting to replace the dark gauges with lighter gauges.
Mike’s LED upgrade definitely brightens things up, but it would be great to have lighter gauges even during the day. I hope someone has found some new gauges that have light faces and have LED lights already built into the unit, and will post about them.
JW Speaker, great Wi. company! Did you get the heated or non- heated LED headlight upgrade?
Also did you get the units with the adjustment slots?
Thanks!
-
As you can see in the pictures below, I removed the existing light socket, which left a hole too big for the New LED, as It would just fall thru. So i added a washer that was larger diameter than the hole, and the used adhesive to bond it to the back of the gauge. Some of the existing light sockets used the gauge case as Ground, i didn’t care because the wires went back to a bank of terminal blocks controlled by the dimmer.