Forum Replies Created

Page 2244 of 2304
  • Archived

    Member
    May 7, 2012 at 6:28 am in reply to: A New Problem

    Sometimes exercising the suspension will get a norgren working, where before it wouldn’t. The spool may have been stuck and now is moving. Jon will go into more detail I’m sure.

  • Archived

    Member
    May 7, 2012 at 6:07 am in reply to: A New Problem

    Thanks for the help, guys. It sounds like we have some disagreement as to the prudence of trying to repair this myself and I will consider all of your input. Thanks much.

    I have not been able to put the bus over a pit so I haven’t laid eyes on the valve underneath to see if it is leaking as well.

    There is one more fact I have discovered that may shed some light on the subject. I moved about 10 miles yesterday and when I parked I left the tag in the drive position, leveled the bus and shut it down.

    I usually lift the tag before leveling because it will drop anyway in 20-40 minutes when my air pressure goes down. I did not lift the tag and 20 hours later the tag has not lifted and the bus has not lowered in the back. That has never happened until this air problem.

    Does that indicate this may be a valve problem? I mean, I like the fact that the tag is holding but it is not normal for my bus but it is definitely holding now.

    Any ideas?

    DKO

  • Archived

    Member
    May 7, 2012 at 5:16 am in reply to: I am the proud owner of a non-contact, infrared…

    I used mine on the way home and had a 2-3 degree difference between a couple of tires measured in the middle of the treads. Is that significant?

  • Archived

    Member
    May 7, 2012 at 5:13 am in reply to: Tire repair needed?

    Thanks all. The tires were all replaced new last summer when we bought it. I will probably take it to Marathon to work on the leans this week, and will have them take a look. Sounds like in addition to have them inspect the other tires when on the lift I can have them put some glue on this one and swap with a tag tire.

  • Archived

    Member
    May 6, 2012 at 10:34 pm in reply to: Tire repair needed?

    Main concern would be safety. A real close look at the cut and if it penetrated the tire casing at all.

    You might want to look at the other tires just in case there was more then one sharp object on the roadway.

  • Archived

    Member
    May 6, 2012 at 3:28 pm in reply to: Tire repair needed?

    I have seen damage like that before. Sometimes it is not a problem, and in others, it can start to chunk out. Being that it is on the steer, I would take it to a Michelin dealer and have them take a quick look to get their input. A steer tire blow out is not fun. I have had a few in trucks, and they all carried less weight on the steering axle than our coaches do. Even if you don’t have an accident if the tire goes out, think of the damage it could, and likely will do.

    Better safe than sorry…

  • Archived

    Member
    May 6, 2012 at 12:25 pm in reply to: Tire repair needed?

    I agree with Jon’s comments. If I were going to anything, I would put some repair cement on it just to prevent it from flapping.

  • Archived

    Member
    May 6, 2012 at 11:44 am in reply to: Wheel Studs

    I am not aware of anyone (Prevost, Alcoa, etc.) liking any type of hub cap whose brackets are captured behind the wheel lug nuts. Having said that however if I were in your position I would view the issue as having three possible solutions.

    The first is to grind or sand the bracket part that rests under the lug nut so its thickness is approximately equal to what you had. Just make sure it is even after grinding or sanding so it doesn’t localize the forces or load on the wheel.

    The second option is to grind the lug nut down to the thickness required to allow the stud to project through it a thread or two.

    Since the first two are kid of band aids my preference would be to not grind or sand anything and just tighten up a lug nut and ignore the fact it is not completely threaded on the stud.

    I can say all of the above because it is just an opinion and since it is free advice it is worth every cent you pay for it. You are not alone with hub caps that mount as you describe and others have dealt with it in the ways described above. I am not aware of anyone that has changed the length of the wheel studs although that is an option (as long as you understand that still will not make Prevost or Alcoa particularly happy about sticking anything between the wheels and lug nuts).

  • Archived

    Member
    May 6, 2012 at 11:35 am in reply to: Rivets Pass Glue

    I was afraid the slides wouldn’t come back in so we did not put them out. I didn’t drive in the dark because I was afraid I couldn’t find the headlight switch, and I never used the cruise control for fear it wouldn’t hold 62.5 MPH to the tolerance level I expect. But as you see from the picture it does run.

    OK, just kidding. We used it all and are loving the slides. It will run with the big boys, and we notice despite strong winds coming home that there was no wind noise although it was strong enough to feel the wind while driving. Still some things to get used to but the transition was relatively easy and now with all of 1600 miles under my belt on this coach I know where the buttons are.

    The trip to Myrtle Beach was through the Smokies and we knocked the 6.5 MPG shown upon the return from FL, down to 6.2 upon return from MB. Both trips the OTR was running, towed the Hummer back from FL but was not towing to MB. Didn’t want to give the retarder a check with the H2 pushing it down the hills, but now that I know the retarder can almost bring it to a stop down those hills I will not hesitate to tow.

    It’s now in the garage, up on stands so maybe tomorrow I can get beneath it in the pit to learn what’s new. I am anticipating little cross over from my solid axle to the IFS, and I know the brakes are different, I know the hubs are the grease type instead of fluid, and I know the suspension is a little different so I have some learning ahead of me.

    All kidding aside I have no fear of the slides or of any of its features. I know it to be a more expensive coach to own and maintain, but not because of reliability, but because there is more to it. The flip side is that the extra room from the slides makes a huge difference in livability.

  • Archived

    Member
    May 6, 2012 at 11:12 am in reply to: Tire repair needed?

    If the cut does not extend beyond the depth of the tread I doubt if any action is needed. Looks like you hit something sharp and it cut the tread but did not pentrate the casing at all.

  • Archived

    Member
    May 6, 2012 at 10:37 am in reply to: FMCA/Michelin Tire Program

    I am at Coach Worx, too, and am facing the exciting prospects of buying 6 new tires.

    4x 365 and 2x 315

    Thanks,

    Ronald

  • Archived

    Member
    May 6, 2012 at 10:05 am in reply to: Rivets Pass Glue

    Be nice! Jon is just getting the hang of that fancy new fangled thing he bought. All those switches and gizmos were probably making him dizzy so he had to drive slow(er).

    Hey Jon, how did those slides work out for you…are you enjoying the extra room? That coach sure does look nice!

  • Archived

    Member
    May 6, 2012 at 7:32 am in reply to: Rivets Pass Glue

    Must be a movie star or a band. Fancy stage coach.

  • Archived

    Member
    May 6, 2012 at 6:24 am in reply to: over head luggage rack

    No…………………A large bank account is a bus owner’s best friend. Tools come next on the list.

  • Archived

    Member
    May 5, 2012 at 9:23 pm in reply to: Heading East North East

    When we travel we look for the flying J rest stops they have ample room to park in the front area as well as a dump station and fresh water fill. Get there RV card and it’s only $50 to dump and you save $2/gal. Showers are very clean (we have an entertainer with no shower on board)

    I agree with Rte 81. Avoid the GW bridge at all costs. They will charge you a $650 toll if you are in tow $13/axle. I tried to reason with the attendant that we look like a bus, drive like a bus so we are a bus so how about just $200. He didn’t buy it and demanded $650

Page 2244 of 2304