Archived
Forum Replies Created
-
Thanks for the tip Tom – Email turned on
-
Great info Jerry and Bob. I have always wondered about access to that area. Thanks for posting your endeavor.
-
Chad’s picture above was what was on m7 ’88 8V92. It is several pieces with left and right hand threads to allow tightening and loosening. There is also a pin at the bottom right of the setup with a cotter pin so you can loosen it up and if the belt is still a bit tight pull the pin, install the belt and reinstall the pin and cotter pin. You might need a 2nd person to help or some kind of pry bar to move it that last 1/4″.
-
Hello, Mike. Thanks for asking. I have replied via email.
Ron
-
Thanks for the quick replies! Where do I get a battery? and what kind?
-
If it’s not too much trouble, Mike, that’d be great. I found a number of photos by scouring for sale ads, and there were a few that look like the Prevost drawing without springs. I just noticed that the drawing I posted that includes springs may only have been for models before 1978. I’m not clear on that. I suspect I’d be okay without a spring in the system, but now is the time to figure it out.
I think I can piece something together off the shelf, but Prevost Parts does have some components in stock. I think they have the rod ends for about $25 a piece. I may try to put something together with stainless steel. McMaster-Carr is a bit spendy though.
-
Well that makes a lot more sense . I thought the outer lug nuts were it. Anyway, I ended up not needing to take it off, as I was able to get to an air fitting I needed to replace with just the one wheel off. Thanks for the help!
-
I pulled the object, it is a short-ish screw that went in about 60 degrees from perpendicular into the tire. It seems like it did not actually puncture it, but I am going to keep my eye on it to see if it loses air.
Given the age of the front tires, I may go ahead and do the tire replacement, mostly depends on availability at this point, as I have a trip to start in 32 days.
-
Archived
MemberApril 24, 2022 at 4:07 pm in reply to: Trying to figure out why AC warning light is onI will post the solution once I figure it out, but thought I would post my current analysis/thinking in case it triggers someone’s experience.
Based on my understanding of the diagram, when AC is turned on, power should go to post 52 to the high pressure switch (NC) and low pressure switch. I verified with AC on, I get voltage at post 52 and 54 as expected in the diagram. I would have thought it would pass through the low pressure switch, energize the clutch, turn off the AC warning light and send power to post 88. What is confusing me at the moment is that the diagram shows the low pressure switch normally open which would block that flow. I tested all of the pressure switches with my ohm meter and all are at normal state (closed or open) per the diagram so on the surface they seem to be good, but I don’t have anything else yet to put my finger on.
I guess I am stuck at what normally gets power to post 88 and the clutch? They jumped around whatever that is but I can’t yet see on the power diagram what to go after.
Hopefully I will get some more insight today as I ponder it some more. If anyone has experience with the pressure switches or this system appreciate any thoughts.
-
Just a couple of observations everyone can ignore if they wish.
Michelin changed there policy regarding tire warranty a while back to base the prorated tire life based on years from the date code, as opposed to tread depth. That is a significant change and is a testament to Michelin in their belief age has become the factor in warranty participation.
But that imposes on us, owners who may never ever wear out tires. If we do not exercise tires routinely we fail to allow the tire, when exercised to release the anti aging components that keep the casing from cracking due to age. We have further concerns if we are not aware of the total tire history. If we or a previous owner drove on tires that were not at a pressure required for the weight carried that tire regardless of age may have been damaged sufficiently to make its worthiness questionable. I have 2017 tires now, and in all previous cases replaced them at 5-6 years. I am going to continue to run them in their present positions for as long as I feel brave. I do know they have never been run at a lower than required pressure.
As to the kit to put a plug in tires that should be treated as nothing more than a means to get the tire to the closest shop to do a proper repair. Should a tire get a puncture a plug is part of the repair, but according to tire manufacturers the correct repair should include a patch on the inner tire liner as well.
If in doubt go to the tire manual for the brand of tires on your coach.
-
Thanks for the feedback. I checked the date code on my front tires, and they are late 2016, so maybe I should consider moving the front ones to the drive axle (replacing this punctured one and another drive tire) and getting new ones for the fronts. My understanding is that fronts should be changed within 6 years and rears within 10, but I suppose there might be a lot of opinions on that as well.
Biggest factor in deciding what to do might be tire availability. I need to look into the Prevost Community Michelin discount as well.
-
Tires are a very sensitive subject on this site, I am sure you will get everything from replace the tire, to if it holds air leave it alone. For me personally, I would plug it, I have done this in the past, and carry a plug set on board for my tires or someone stranded and in need. It is solely based on your comfort level.
I have a couple of these kits.
https://www.amazon.com/gp/product/B01HUIOJBA/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1
-
I do the same with the aqua Hot.
-
Greg, for my 8V92 I use Napa Gold # 1970 for the Engine. Transmission I use FleetGuard # HF6243. Engine Filter: Detroit # 23530408