Jon
Forum Replies Created
-
John, I think you are stuck with reprogramming because the multiplex system is always measuring every circuit and comparing the current against what it is supposed to be. I do not know if the tail lights are engaged through a relay external to the modules or directly through the modules, but I strongly suspect it has to be a programming change if they are allowed to do it. It might be a DOT requirement to light the brake lights even if the braking is only supplemental braking like a Jake or retarder.
Give them a call and if you find out let us know.
-
Thanks Jon for your reply, If air is leaking out of the discharge port of the abs valve while airing up the tanks ( with shop compressor ) to me it implies the relay valve is leaking and carrying over to the abs valve…but it is only on the right side abs valve, would the left not leak as well..? The relay valve mounted on now is the second relay valve I’ve install and I was thinking surely two of these could not be bad ( both are new not original Bendix but reman. ) I guess I will order one from Prevost and see how that goes.
-
What type/size are you batteries? Lead acid or AGM? Voltage?
Am I to understand you only have one inverter/Charger? As mentioned, 8 batteries are a lot for one inverter. Unless you have 8 – 6v batteries wired series-Parallel giving you the equivalent of 4 – 12v batteries.
In any case if they do not last long that would be the place to start.
-
Luc, I worded my comment/question about shore power through inverters wrong.
All inverters pass through shore power, but Vantare as an example runs all circuits via inverters, whereas most other converters have their conversions set up so only specific circuits are powered by inverters or power passed through the inverters from shore or generator.
Bernie made the best observation of the day with his comment about batteries. Heed his advice.
-
Doesn’t read your posts. Thank Goodness!
-
Hi Jon-
Yes, it appears that shore power is going through the inverter as well.
I have not been able to plug in anywhere since purchase, but while at the former owners home, while connected to his 30amp shore power, the inverter was showing it was charging until it reached “float status”.
The bus had a ‘Trace” inverter built in, which must have stopped working at some point, so he put in the Magnum system.
I’m not sure what the current setting for the inverter is, not sure how to determine that.
Yes, I’m not sure he wired it himself, but it is possible, as he has done other projects on the bus. I can post photos if you tell me what to take them of.
Thanks!
-
I will ask. Dr. Google didn’t yield anything so I was thinking these were Country Coach proprietary codes.
-
We’ve had only one RV (our Liberty) so I’ve never had to manage separate black and grey tanks. I like having a single holding tank with grey water bypass to manage. If we were buying a new Liberty bespoke, I’d likely spec a single holding tank five gallons larger than the fresh water tank. Right now I have 200 gallons fresh and 175 holding. You can’t squeeze 200 into 175.
If we’re on FHU’s and clothes are being washed, I’ll leave the valve on the holding tank “open”. With the black and grey sources going through the single tank, I don’t worry about a “pyramid”.
If we’re dry camping without a sewer hookup, I’ll often open the grey water bypass (if I can discretely). Toilet water goes into the holding tank along with whatever else went into the toilet so there is water in the tank to help break up the solids. After a weekend of dry camping at the race track I watch the holding tank dump through a clear plastic elbow and its mostly water.
I’m on a Facebook RV Horror Stories page and some of stories about RV owners who don’t understand their plumbing systems are oftentimes difficult to read. That was the first time I heard the term “pyramid” used in reference to camping and RV’ing.
-
Mike T. When we bought our 1992 XL in 2009 with 8.25 wide alloys wheels and its original 12R’s tires, we upgraded to 315’s. Thats when we discovered Michelin had two different pressure charts. One for 12Rs on 8.25 wheels and one for 315/80/22.5 mounted on 8.25 inch wide wheels. Since the 315 is leaning towards being a bit pinched on the narrower wheel, Michelin has a slightly lower psi on chart for weight carried. In our case, made for a softer smoother ride.
-
Jon and I are in lock step on this subject!
There are two things that will send shivers up my spring …
hearing the racking of a 9mm behind my ear and hearing the shower drain gurgle while the clothes washer is draining.
-
I’m with ya Jon. The wife and I still have 3g flip phones and like it that way.
But att has informed us that come Feb of 2022 they are shutting down their 3g system and we’ll need to switch to 4g/smart phones.
We are not looking forward to it.
-
I had same issue so used only 3M adhesive without screws. Relocated the holdowns for cables etc. to the steel ceiling framework between panels.
-
Yes it’s a XL40 not much weigh on it other than
the 12 kw Powertech generator. Thanks for the
info! I was thinking the pressure was to high.
I use to run the old tires @ 90 on the rear and it
never was bumpy. It was very smooth.
Thanks Eric
-
I installed only 3 or 4 screws when installing the soundown for that very reason.
Spray adhesive (I have forgotten which one but it may be in one of my prior posts) is working well.