Jon
Forum Replies Created
-
-
Thanks Don so it should be pulling air out thank you very much. Jim
-
John here is a phone number for a gentleman in Naples Fl about a month ago he had some wheel covers, 630 878. 4399 ,hope this will help you.
-
Call Meritor Express first – 888-725-9355
Here are some linings, you’ll need the 48 bolts & nuts that hold them onto the shoes, Prevost# 641208 too: LINING LINK
Here are the shoes w/linings already installed: SHOES LINK
-
I use Locktite 545 and am very happy with it’s performance.
-
Hi Luc, This is a Highly debated conversation, working with air fittings for 30+ years on high speed automated assembly equipment, I use teflon tape and paste depending on the application. The pro’s and con’s for me are below:
Pro’s for using Paste
1) It is a paste, so in theory you would get better adhesion to the pores in the thread surface.
Cons for Using Paste
1) Messy
2) Can contaminate valves if too much is used
3) Not the best when you can only apply it to one of the two surfaces. As you thread the fitting in, the top thread tends to wipe off the thread sealant, leaving a mound on top.
4) If you don’t seal the cap properly, it will dry up and be unusable
5) replacing the fitting requires a lot of clean up and high chance for valve contamination, as sealant will drop into valve spool as the fitting is removed.
Pro’s for using Tape
1) Easy to use
2) No Mess (this is a big one, thread paste gets everywhere)
3) Doesn’t dry up or expire, always there when you need it
4) removing the fitting and resealing is much quicker.
Con’s for using Tape
1) You must be careful what direction you apply it. The wrong direction it will un-thread itself from the fitting
2) You must wrap more than one revolution. I use 2 or 3 turns.
Thread paste i use:
https://www.amazon.com/gp/product/B002BY02PQ/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1
Teflon Tape I use:
https://www.harborfreight.com/12-in-x-43-12-ft-thread-seal-tape-10-pk-63943.html
Another thing I do when working with pipe fittings is I wire brush all the razor sharp edges off the threads before i use them. These fittings are being fabricated cheaper and cheaper these days, and if you look closely at the threads there are many fine burrs on the threaded surface. Wire brushing them or using scotchbrite will soften the edges. I hope this helps.
Interesting paper with some more information:
-
I watched the video when he first published it. What a beautifully cared for coach. Unique. Someone had, and someone now has, a great ride. I hope to see it some day out on the road.
-
I guess dragging brakes was not a proper term. I assume brakes are designed with the starting point that braking will slow the vehicle down thus limiting the amount of time and intensity that the system sees. Putting a small passenger braking system partnered with a 50k lb. Commercial vehicle defeats that limiting factor. I imagine that the bus just pulls right through whatever braking the towed applies.
I have never had a brake system on my towed. If i were to the only kind i would be comfortable with would be a surge type system. The towed vehicle only brakes with forward pressure on the hitch. I am not sure if this type is avallable.
-
Ouch is an understatement.
Assuming cause was toad brakes would a TPMS with temperature monitoring have caught this? On sharp turns I try to watch toad wheels to confirm they are rolling as expected. Also when hooking up wife & I do a roll test to confirm the toad is rolling and brake lights work.
Cases like this make me wonder if toad breaks for a small less than 5,000 pound load are really needed.
-
Thank you for your reply, Bernie!
I just got off the telephone with Marshall who guided me to the “known” wiring harness location where his tech informed him last October where the wiring commonly rubs through the wire loom / wire insulation.
I carry jack stands and will check it out asap. IF this is the cause, and not simply the failure of the OUTPUT Speed Sensor (code 25-11) I will repair it here in my campground, then also pick up a new sensor prior to leaving our current campground.
***Marshall state the location is upon the engine oil dipstick fill tube on the 14L Series 60. I will followup and include a photo if at all possible. MY “symptoms” were identical to Marshall’s symptoms.
-
If I remember right there are 3 sensors on the trans that can cause erratic conditions. My issue was an 06 chassis too.
Mine was the wiring clip going into a sensor on top of the trans. I was in PHX and also Williams sent a tech out who knew the location and reached up unplugged it and rewired the clip and all was well.
There’s a number of places this can happen or it could be a sensor.
Are you anywhere close to have someone put a reader on it?
Later
bv
-
Another sensor I’m carrying is the crankshaft position sensor located curbside
lower left down at the balancer. Failure results in a no start, Part # 8929388
-
I did indeed think of bypassing the oil sensor with a jumper. I did not make that my first shot at getting back going because as Jon said if there really was 0 oil pressure the engine would be toast.
I do have an OTC engine/transmission oil pressure test set, but it was at home on a shelf, doing me no good on the fateful day.
I bought a pressure test guage at OReillys while I was in Farmington. This is not really a test tool, but designed to be installed in a vehicle to give a mechanical analog reading of oil pressure. Comes with a 2″ gauge, some very small and fragile looking hard plastic tubing, matching compression fitting on back of gauge and a provided matching 1/8″ male compression fitting as well as a 1/8″ to 1/4″ brass bushing. Just what I needed to test oil pressure, the oil sender hole in block is female 1/4″ pipe. I detailed what I planned to do with this in my last post, but ended up not needing to use it. I mentioned earlier, I am likely going to install a mechanical oil pressure gauge somewhere visible on the engine. I may use the gauge from this kit, but will likely install it with a manual shut off small ball or needle valve between the engine oil pressure source and the gauge. I just don’t fully trust a $26 dollar gauge from China enough to add it as another potential oil leak point carrying full engine oil pressure going down the road.
Had I not been able to get a new sensor, but could get the oil pressure verified with the above gauge, I probably still would not have jumpered the wires unless I could have gotten verification of which pins to jumper. The wiring diagram in the link below shows a ground, an EOP (engine oil pressure likely) signal, and 5V+ as the three wires connecting to the sensor. My fear was as the other end of these wires likely connected to the ECU, if I sent aberrant voltage (the full 5+) or grounded the signal lead to the ECU there was some risk of frying the ECU.
My guess is the Sensor functions by an internal transducer varying the signal voltage from some low to high value based on the oil pressure it sees. Maybe some day when I get a spare moment I’ll put together a set up shown in the 5th box in the link below with my yet to be purchased spare oil pressure sensor and see what happens with signal voltage as pressure varies. I’m not holding my breath until that day.
As Lonestar said he was going to do, I am going to buy spares of all three “shutdown causing” sensors and install the other two, next time I get to working on the bus at home.
-
Great explanation David. Your posts are always very helpful.