Forum Replies Created

Page 82 of 2304
  • Archived

    Member
    February 11, 2021 at 7:28 pm in reply to: Can I post a PDF to the Forum?

    I’ve never figured out how to post a pdf? I do one of the following:

    1) find the pdf on the web and post the link
    2) copy and paste it
    3) screen shot
    4) take a picture of it and post the pic
  • Archived

    Member
    February 11, 2021 at 2:32 pm in reply to: Hard Freeze in Houston

    Thanks Dick – the local weather gurus are forecasting slightly lower temps – like you stated with a little wiggle room, which still causes concern. I did notice a thermostat in the water bay to control heat – I’ve got a few days to make preparations and it sounds like I’m going to have a few sleepless nights but we’ll survive – beats the crap out of a hurricane!

  • Archived

    Member
    February 11, 2021 at 12:12 pm in reply to: Hard Freeze in Houston

    Yes… you need shore power as your batteries will need to be charged since the webasto uses DC voltage and will drain your batteries.

    The question is whether or not your shore power is sufficient to enable use of your battery charger.

  • Archived

    Member
    February 9, 2021 at 10:05 pm in reply to: 2000 Featherlite XL Vantare Charging?

    Vanner has a good web-site and reading about the vanners it talks about batteries A 24v and batteries B 12v and it says they have to have the same amp hr batteries, how do they do that with house battsa lot of amp hrs verses 24v batts 2 of them, I guessthat”s why they have 2 EQ’s

  • Archived

    Member
    February 9, 2021 at 8:19 pm in reply to: Picture Test

    Harry, paint is original we only changed the Awnings . Thank you for the compliment. We just like to keep her looking good like most other owners of these fine machines .

  • Archived

    Member
    February 9, 2021 at 6:37 pm in reply to: Steering bay 3 way Norgren valve leaking air

    Now every other day leans to right. Start aux compressor and level up.

  • Archived

    Member
    February 9, 2021 at 3:10 pm in reply to: Norgren Pressure Regulators

    Jon,

    I remember reading in an article you wrote about modifications you made in your air systems that pressure regulators are notorious for leaking. This regulator is for the pocket doors. Could a valve failure downstream at one of the doors, they both still function, cause the pressure leak at the regulator?

    Thanks

  • Archived

    Member
    February 9, 2021 at 2:42 pm in reply to: Possible Head Gasket issue

    So here is what we found to be the issue . I was told those lines should not be their .

  • Archived

    Member
    February 9, 2021 at 12:05 pm in reply to: 2000 Featherlite XL Vantare Charging?

    Art, now mine is a 98 XL however maybe batts are the same . In the bay where the house batteries are on a side wall or above their is separate 12/24 balance for charging . Mine had gone bad and i replaced with the vanner as it was all i could find and did the same . If a pic is needed tex me because I have idea how to post from my flip phone 🙂

  • Archived

    Member
    February 8, 2021 at 7:22 pm in reply to: Norgren Pressure Regulators

    Thanks Jeff and Tim,

    I didn’t provide enough info in my original post.

    The new regulator is the same model as the original one, R73G-2AK-RMG. It is a relieving model. I am assuming that it is correct, because it is the same as the one that has worked for the 5 years that I’ve owned the coach.

    The new replacement regulator is plumbed the same as the old regulator based on the arrow on the base.

    When I replaced the regulator, the compressor went from running every 30 minutes to about 5 hours. I have been chasing other leaks, but the regulator was the biggest. Now the new one is leaking and it’s back to every 30 minutes.

  • Archived

    Member
    February 8, 2021 at 9:38 am in reply to: What is this Box???

    Hey Jeff! Thanks’ for reply your the only one. What is it’s function? What does it do? It looks like it gets power from 24v ignition sw to DDEC decell sw CB breaker 92 same breaker powers level low,ties to world trans speed signal, tied to speedo.

  • Archived

    Member
    February 7, 2021 at 10:59 am in reply to: Possible beginning of runaway engine???

    I just cleaned the guides/rollers and made sure it would travel back to the idle position. No problems in the last 5 or so years.

    Replacement would be easy if the actual rheostat (potentiometer) is the problem, i.e. not giving smooth continuous read-outs or developing dead spots. The pedal assembly is just plug and play.

  • Archived

    Member
    February 7, 2021 at 10:48 am in reply to: Possible beginning of runaway engine???

    We have experienced very similar symptoms on occasion over the last 2-3 years. The first time it happened I immediately hooked up a code reader, but there were no active codes. Suspecting a possible fuel issue, I changed both fuel filters and the problem went away, only to return a few days later. Since then it comes and goes intermittently with no obvious pattern. After much online research, discussions with experienced DD 2 cycle mechanics, etc, we still see it from time to time. However, a while ago I learned that when it occurs if I quickly and strongly “punch” the accelerator pedal, the symptoms go away.

  • Archived

    Member
    February 7, 2021 at 9:55 am in reply to: All Aux Air Filters Replaced

    It is often talked about how clean, dry aux is critical.

    Here is a link that discusses how coalescing filters remove sub-micron particles AND all moisture.

    The filters replaced were in use prior to installation of the coalescing filter I added on my bus last year, so will be interesting to monitor how clean the new filters remain.

    When parked and using aux air, the coalescing filter is in advance of all devices using air.

    https://www.hydraulicspneumatics.com/technologies/air-filters-and-frls/article/21882919/sizing-and-selecting-frls

  • Archived

    Member
    February 6, 2021 at 7:08 pm in reply to: Possible beginning of runaway engine???

    More likely a sensor issue since rebooting the ECM seems to have fixed it.

    Check your electronic accelerator pedal (just a rheostat) and make sure it is not caught on anything. Lift it off the rollers and reset it. Turning the engine off and on will re-establish the digital throttle range.

    I had a similar problem a long time ago. The jake brake would not engage going down a mountain. The cause was my accelerator pedal not returning to full idle. The ECM reads the digital idle value from your pedal upon start.

Page 82 of 2304