Forum Replies Created

Page 73 of 2304
  • Archived

    Member
    April 4, 2021 at 5:44 pm in reply to: Recommendations for RV Campgrounds in Phoenix area

    Also any suggestions around Zion Nat. Park in Utah? Willow Wind near by was recommended by an acquaintance but not sure of his understanding of what a big rig needs. Thanks.

  • Archived

    Member
    April 4, 2021 at 2:30 pm in reply to: Separation between Chuch and State

    #2 – More Air System Info

    Burketts valves were what Prevost used in the mid to late 90s as a replacement for the Norgren three way valves. They come either NO or NC and they cannot be altered. The first versions of the valves did not have a return spring in them and we had numerous issues where the valve would stay in the midway position. This led to air systems not building air correctly. Normally the bad valve was on the tag lift system and by simply cycling the system you could get the valve to seat itself and the air would build correctly. Burkett came out with a valve with a return spring ( the new Burkett valve) but we went back to Norgren valves eventually. Another issue with the Burkett valves was they were made for a much cleaner, industrial application. The coach pneumatic system in not a completely clean and dry environment. The Burketts did not fair well on the coach. The Norgrens were more robust and did not mind a little oil and water in their working environment.

    Most of the people in Prevost service do not know anything about the Norgren numbers. Prevost parts secures the correct Norgren number for the application from the engineering department and then a Prevost part number is generated. To get the Norgren number we would have to get someone in parts to look at the cross reference file for the correct Norgren number. That is why you may get a blank stare from a tech if you come out with a Norgren part number.

    As noted also above the type of valve you need (NO or NC) will be dependent upon your pneumatic configuration in the rear of the coach. Up through 1996-1997 the plumbing of the tag axle lift circuit required that there be sufficient air pressure in the auxilary air tank air sytem to properly pilot the valves associated with the tag axle and tag lift system. Thus you needed good aux. air pressure to keep the coach at normal ride height in the rear of the vehicle. Lack of proper air through an air leak would eventually reduce pilot or control port air pressure to the point where the internal spring tension of the valve overcame the control pressure and the system cycled much the same as if you had flipped the tag lift lever. The difference being that there is no aux air pressure left to do anything with the system.

    Engineering at Prevost redid the pneumatic “plumbing” of this circuit in 1997 so that there were no control pressures to any of these valves to keep the tag axle down and the tag lift circuits off. There was a maintenance bulletin released “Service Bulletin 96-14B) to increase the reliability of the pneumatic system. The bulletin can be found at:

    https://secure5.volvo.com/technicalpublications/pdf/Sb96-14B.pdf

    There were various kits made at the time for different models. These would come with instructions and valves that had the proper brass fitting for the application. The kits also included an inversion valve that had to be plumbed into the circuit. Prevost has always cancelled the brake boosters on the tag axle when it was lifted to prevent tire damage. As we were changing the way the axle was controlled we had to change the control of the Bendix R12 valves that controlled whether there would be brake application pressure sent to the boosters on the tag axle or not.

    The modification takes some time as the old valves need to be removed and air lines properly identified. Then the new valve installed correctly and the inversion valve installed. Plus the light circuit in the dash had to be changed to reflect the lack of air pressure in the controls when the vehicle was in the normal ride height position.

    All that being said: to check your system! Run vehicle and get all air tanks filled. Turn off coach. Open accessory (auxilary) air tank and bleed down the pressure. If the coach has the newer system installed the vehicle should NOT settle in the rear as if you flipped the tag lift lever. If if does squat, then it most likely did not have this modification done.

  • Archived

    Member
    April 4, 2021 at 2:24 pm in reply to: Separation between Chuch and State

    Bill I’m gonna try and answer your question(s). I will do it in three separate replies. I got this info, saved it to my log book, here on PC from “Prevost Service”. I hope this helps.

    #1 – Air System Info

    Let’s start with where the air starts; the supply system. The heart of the supply system is the engine driven air compressor. It feeds an air dryer that removes moisture and oil. The dryer feeds the wet tank and a return line to the compressor mounted governor. The governor signals the air compressor to stop producing pressurized air and the dryer “sneezes” to unload the pressure line when the governor set air pressure has been met.

    The wet tank then supplies air to the front and rear brake main tanks and the auxiliary tank. To isolate the front and rear braking systems, air entering these tanks does so through a check valve at each tank. Once air is in the main brake tanks it cannot escape back into the supply feed.

    The auxiliary air system cannot have the same priority to supply air as the braking systems. To ensure the braking systems are fulfilled before the auxiliary system, the supply line is fed through a protection valve to the auxiliary tank. The protection valve opens when either side of the valve reaches a specific pressure which is somewhere between 60 and 75psi. If your coach’s air systems leak over time you may have noticed that air builds in the front(secondary brake) and rear(primary brake) systems first. At the rating of the protection valve you then hear the rush of air entering the auxiliary system.

    That is basically the entire supply air system. It supplies all 3 main air subsystems, rear braking, front braking, and auxiliary. Once those systems are filled the governor effectively turns off the compressor and each of the 3 systems are protected from their air returning to the supply air system.

  • Archived

    Member
    April 4, 2021 at 12:20 pm in reply to: Damn that Tom

    A problem Jon will never experience …

  • Archived

    Member
    April 4, 2021 at 10:12 am in reply to: Michelin Tire Problems

    Jon:

    Thank you again for forwarding the info.

    You just noted SHE in reference to the Michelin representative. I hope the SHE is not Tracy Johnson.

    Tracy Johnson is who I have been communicating with and Tracy has taken a firm stance that the Michelin authorized dealers I have dealt with are reputable stores, know what they are doing, and after speaking with the stores I had visited she has informed me the stores installed/mounted my tires per Michelin specs and the stores have had little to no past customer complaint’s. Tracy has shown no interest in even trying to assist me as a customer and at least offer to thoroughly inspect the tires to prove or disprove my concerns. Her best offer is for me to return to the stores that didn’t do it right in the first place and let the store decide as to my fate.

    Chuck

  • Archived

    Member
    April 3, 2021 at 8:52 pm in reply to: Michelin Tire Problems

    Jon:

    Thank you for passing on the post. I obviously need to move up the ladder from the rep I am currently dealing with.

    Chuck

  • Archived

    Member
    April 3, 2021 at 4:56 pm in reply to: TSD Fuel Program

    Go to App Store and search for TSD Open Roads app. All prices are there

  • Archived

    Member
    April 3, 2021 at 1:04 pm in reply to: TSD Fuel Program

    Same here. I will send an email, but with the holiday weekend a response may not come quickly.

  • Archived

    Member
    April 3, 2021 at 12:40 pm in reply to: Michelin Tire Problems

    Michelin monitors this site and from time to time has responded to a post.

    I will copy your post and email it to a contact I have at Michelin and also to a Michelin customer service.

    We spent a considerable part of a morning at a Michelin shop dealing with runout on tires mounted on a truck. There are two potential issues, both with the same results that I will repeat here because they are important.

    First, seat the bead on a tire with the tire and wheel in a horizontal position, such as with the wheel sitting on a 5 gallon pail. The ring around the tire in Al’s post needs to be uniformly spaced around the wheel. If not, deflate the tire, break the bead and do it again until the spacing is uniform.

    But there is a second concern. Whether the tires are hub centered or stud centered it is possible for the wheel to be mounted in a position that is not concentric with the hub. If the wheel can be rotated after mounting, a dial indicator against a rotating tire will reveal no runout or a large runout. The fix is to position the spot on the wheel / tire with the greatest runout at the top of the wheel position. Loosen the lug nuts, allow the wheel to drop and retighten the lug nuts to spec. This will have the effect of centering the rotating wheel and tire assembly and reduce the runout.

    When a tire with runout is driven it will feel like an out of balance tire. It is not, and if allowed to wear based on that runout the out of balance feel will get worse. Eventually no amount of balancing will correct the feeling, and only shaving the tire will correct the problem. If the runout is too much, nothing will correct the problem.

    I am sure we all have witnessed technicians working on our coaches, doing stuff we know is wrong. It can range from over greasing fittings until the rubber boots fail, to mounting tires in wheels in the wrong way. I am sure if we have mentioned the errors the response is that is how we have always done it. Our option is to swallow hard and go away, or to make sure the shop and its technicians understand the work you are paying for has to be done correctly. Bus owners are often treated like morons because everyone knows if you have money to buy a bus, it is likely you aren’t smart enough to maintain it.

  • Archived

    Member
    April 3, 2021 at 8:23 am in reply to: Crc Freeze Off

    From a old Snap on dealer this is why you should get a pipe plug socket. No ball so way stronger.

  • Archived

    Member
    April 2, 2021 at 2:01 pm in reply to: oil preference

    Any name brand 15w40 that is rated for compression diesel engines.

    I’m currently running Shell Rotella T4 15w40 in our PowerTech 17.5 w/Kubota engine.

  • Archived

    Member
    April 2, 2021 at 12:54 pm in reply to: Massive Detroit Upgrade

    I’m surprised Tom didn’t tell everyone he finally sent me the dues money he owes me, of that I now have a Smart Phone that I actually turn on.

  • Archived

    Member
    April 2, 2021 at 10:52 am in reply to: oil preference

    In all three coaches, I used 15-40 Delvac. Same as the Detroit used. My Volvo used 10-30. Readily available and met the spec for the Yanmar in the Kohlers.

  • Archived

    Member
    April 2, 2021 at 12:22 am in reply to: Silent Gliss Remote

    Dan,

    Isn’t that covered by your warranty from Big Al?

  • Archived

    Member
    March 30, 2021 at 10:15 pm in reply to: Fiber optic lighting

    Will let you know if I can’t get it going.

Page 73 of 2304