Archived
Forum Replies Created
-
I was not aware there was a factory adaptor. I believe I purchased mine from Camping World.
-
I wish I found this thread before I changed my output seal last time, about 5 months ago. After I changed it out, leak seemed to be gone, but after a recent trip, I have trans fluid everywhere again. I suspect it is the yoke surface chewing up that seal. I guess I’ll have to figure out if I do the “farmers trick” or get that sleeve -I had no idea those existed!
And BTW, holy hell, can this create a mess! I have never been so dirty in my life, and I am about to do it again. Hopefully this will be the last time. I did not really clean much up under the bus last time, as I was on a time crunch, but this time I feel compelled to try to clear all the crud out. It’s just going to take a lot of de-greaser.
Not sure if I have a leak with the retarder, but I doubt I can tell until the leak at the seal is taken care of.
-
I know nothing about auction houses so if they are not legit, that’s news to me. Maybe I should have said Name brand? Buyer beware even there? I would never be at one so just consider my comment as ignorance.
-
“Legitimate car auction house” … is there a such a thing? Asking for a friend.
-
Thank you. Lots of information.
Are those Gates numbers for caps you have ordered and used? They say 2″ and I believe mine measures 2 1/4. I will recheck in the morning.
Davy
-
Jessica is out of town but aware. She will respond as soon as she gets to her computer. Remember we can always be reached by email as well.
Bill III
-
I have been a member for over a year and I had no idea we had a classified section. I guess I better look around more.
-
Archived
MemberMarch 20, 2022 at 4:03 pm in reply to: Clean sheet design: inverters, batteries, etc.Please post pictures as you go along, my washer/dryer was the first thing thrown in the scrap heap when i brought my bus home. We now use that space for Trash and storage. I am a big believer in making the bus a space to suit your needs not a future owners needs.
-
Archived
MemberMarch 20, 2022 at 3:35 pm in reply to: Clean sheet design: inverters, batteries, etc.I mentioned earlier that it would be a wonder if I ever finished this project. Well, I have since decided to completely gut the interior of the bus and start from scratch. I was becoming less enthused about doing so much work on a bus with such a dated interior. Despite the significant added work involved, I’m excited to have a true “clean sheet” going forward.
In doing this, I was able to completely remove the OTR ducting and coolant/refrigerant lines from the interior floor-to-wall junctions. I have also completely removed the three Cruisairs, and they will not be going back in. I also removed the Espar hydronic heating system, which simplifies the rebuilding process. Those radiators on the walls were really in the way. I also am able to re-prioritize my use of space, sacrificing the washer/dryer, dinette, oven, and ice maker to add needed size to the bedroom, shower, and kitchen storage.
I’ll post a new thread on the rebuild, but thought I’d update this one for now. The only guaranteed result is that I can no longer call this a Liberty Coach. It will be unrecognizable as such!
-
The worst place to put old possibly bad tires is on the tag. In my experience any tire with an issue ranging from uneven wear to cupping and other problems gets eaten alive quickly in the tag position.
I have no idea why.
-
Thats good news Mike! Keep us posted on your new charging system.
I finally got a chance to dig into mine further. My access panel was exactly like yours. Unfortunately Marathon decided to carpet the bedroom one peice and set the bed cabinet on top of the carpet. Not only that the panel ran 6 inches under the bed. From looking at your pictures i was able to determine where the buried screws were. i cut some small slices in the carpet to remove them. I had to cut the floor panel in half to remove it.
Once i got in there it was much easier to get to the terminals to troubleshoot the no charge situation. The first thing that i noticed was that there was no ground bar from the field ground terminal to the alt case. Hmm. Every 50dn that ive seen has that including the new one i bought to replace the original. I took the ground bar off the new one and put it on there. I started the bus and the volt meter on the dash pegged to 30v. I shut it down immediately. After doing some further research i determined that my regulator is a low side regulator so it regulates the charging on the negative side of the coil. With a dead ground the coil signals full unregulated charging. I removed the ground strap removed the new regulator that i installed a few weeks ago and put the old one back in and bingo, 28 volts on the dash. My problem turned out to be just a loose connection on the field ground terminal.
Apparently they no longer make a regulator that controls the low side so if my regulator ever dies i will have to change the wiring over to high side regulation.
Yet another lesson in “check your schematics”. Your bus may not be the same. Some times i forget to listen to Jon.:) Has anyone ever heard of a low side regulator?
Im back to a working alternator now. My next task is to modify the panel so to fill in the 6 inches of panel under the bed and make a new one that is only outside of the bed.
I very much appreciate you taking the time to document and share your work. That goes for everyone here who does the same. Thanks guys.
Jeff
-
Ok I have about 100 miles on the Bus since I pulled and capped the 50DN, all looking good so far.
-
Yeah tried to post a Pro Link 9000 scanner up. No Joy.
-
We changed the locks on the fuel doors of our coach to some that were more uniquely keyed. It was easy to do. I think that we had to swap the “wing “part of the lock from our original locks to the new ones for a more precise fit.
Or have the original locks re-keyed, if you can find a locksmith.
Just another possibility.