Forum Replies Created

Page 2247 of 2304
  • Archived

    Member
    April 29, 2012 at 7:05 pm in reply to: Need help getting right rear compartment on H3-45

    BK,

    I sent Prevost a link with a request for some help. I hope they can help.

  • Archived

    Member
    April 29, 2012 at 4:16 pm in reply to: fuel gauge

    good day folks. got my fuel gauge to finaly work. previous owners thoght they should wrap the sender wire in electrical tape and hide it under the dash. when i ground out the sending wire my gauge jumps to full. i am suspecting a faulty sender. my question is. can i use any sender or does it need to be a 24 volt sender.

    thanks and hope you all have a happy day of bussing.

  • Archived

    Member
    April 29, 2012 at 3:37 pm in reply to: Failed Adhesion on XLII

    Thanks for the info.

    glen

  • Archived

    Member
    April 29, 2012 at 7:16 am in reply to: RE: My Broken Big Bus…..Again!

    Pat,

    This would be easy in person, but here goes.. The analog
    multimeter went out with the hula hoop, sorry, you need a digital,
    but what you have will work fine. The basic function of the meter is
    to measure voltage, AC/DC and continuity. The red lead is for the
    positive + and the black lead is negative -. You have to be sure your
    on the correct scale to measure AC and DC.

    Hold the red lead on the positive side, the black lead on the
    negative side and then read the voltage. If your meters needle takes
    a nose dive, you have the leads reversed. I
    suggest you don’t do anything involving AC, leave that to the
    experts
    . DC is low voltage and you will be dealing with 12 and
    24.

    Continuity is just a way to test current flow. To try this, just
    take a simple 12v fuse and touch the leads to each side of the fuse.
    if the fuse is good, you will hear an audible sound from your meter.
    With the meter in continuity, touch the leads together and you will
    hear the audible sound. You can also check ground in the same manner,
    by touching the lead to a known ground and the other to the
    connection your testing.

    As for your problems with the bus, it could be anything from the
    switches, fuse, relays or loose wires. You told me your bus got fried
    with a lightening strike causing major damage. Did all of these light
    problems happen after the strike?

    All of the above is just basics with the use of your meter. The
    meter has many capabilities that cannot be explained here. You should
    have got a user manual with it and if so, be sure to read the
    instructions. If you have any doubts, DON’T experiment with voltage.

  • Archived

    Member
    April 29, 2012 at 5:01 am in reply to: Rear rock guard/ mud flap

    I don’t see why not.

    If you go here and put in the data for your coach look under the technical information, section 9 and it should give you confirmation of that. http://prevostparts.volvo.com/technicalpublications/en/manuel.asp

  • Archived

    Member
    April 28, 2012 at 9:57 pm in reply to: 3 Amigo’s OKC Gathering

    Tom, I am sorry to inform you that is not Jdub’s home made ice cream machine, it’s Marathon’s newest modle macerator pump he had installed on his new ride.

    I would like to be there to. Count me in.

  • Archived

    Member
    April 28, 2012 at 7:31 pm in reply to: Found One of My Air Leaks

    I think the correct phrase Paul is “work in progress.”
    It just never ends, but at least you get to know your bus up close
    and personal.

    My aux will bleed off to zero in about 24 hrs and I have checked
    every fitting, component and norgren that is accessible. There isn’t
    any compartment or panel that I haven’t removed looking for leaks.
    Then a few days ago I had the bus out running and when I put it back
    in the barn, the aux held up for 3 days and I still had 30 lbs. Woo
    Hoo, I’m happy!

    One day I’ll get to Livingston, TX and the ole bubble tight guy, Hector, will help me with his magic.

  • Archived

    Member
    April 28, 2012 at 3:11 pm in reply to: Myrtle Beach, April 30 – May 5th

    Bob and I will be there on the 30th. Slot H 69, it’s as close as we could get at the time we made our reservations. Hope to see you all there!

  • Archived

    Member
    April 28, 2012 at 12:34 pm in reply to: Petty Complaints

    Point well made !!!!!!!!!!!!!!

    Tell them you own the best of both worlds, well almost, it’s not a CC.

  • Archived

    Member
    April 27, 2012 at 10:23 pm in reply to: Petty Complaints

    Hey Jon, if you want to stop all these (kind folks) from harrasing you about your new coach, just add rivets to it like your old one and silicone the slides shut and you will be back to a no slide rivet coach.

  • Archived

    Member
    April 27, 2012 at 8:39 pm in reply to: Rear rock guard/ mud flap

    Tom

    I second Chuck’s request. I have a pic of the unit available from Detriot but they want $250 for theirs and I am pretty sure I can build one cheaper than that. I would love to see a home made version if you have a pic you could post.

    Rob

    91 LeMirage XL

    Missouri

  • Archived

    Member
    April 27, 2012 at 2:50 pm in reply to: Rear rock guard/ mud flap

    No major leaks. I made a catch can for the slobber tubes and have a small leak at the power steering pump.

  • Archived

    Member
    April 27, 2012 at 2:20 pm in reply to: level low norgren control center

    When you send a command from the dash switch the solenoid valves open as required to shift the 3 and 5 port Norgren valves, which in turn do the function you are seeking, such as energizing the 3rd solenoid valve down to shift the five port Norgrens so the ride height valves are functioning. When you switch to another command or turn off the key those solenoid valves close. When they close the air used to shift the Norgren 3 or 5 port valves is exhausted and that is the puff of air you notice.

    If you merely closed the valves without releasing that puff of air which allows the Norgren 3 or 5 port valves to shift to their normal position the last command would still be in effect and the valves would not return to their normal position. Think of the puff of air escaping as a cancellation of the previous suspension command.

  • Archived

    Member
    April 27, 2012 at 12:35 pm in reply to: Failed Adhesion on XLII

    Prevost model year 2000, most likely titled by a converter as a 2001 was the first year with no rivets.

  • Archived

    Member
    April 27, 2012 at 12:28 pm in reply to: Need help level low switch

    Whatever switch position energizes the center solenoid valve is the drive position. Just hook your volt meter to that valve’s input and when you see 24 volts the switch is in the drive position and all other positions are then as described above.

Page 2247 of 2304