Forum Replies Created

Page 109 of 2304
  • Archived

    Member
    October 24, 2020 at 2:50 pm in reply to: Chasing air leaks

    No, but Big Al did once try smoke while I watched holding his beer. Smoke didn’t work, ya had to be there, then he left that stinky smoke machine in my garage.

  • Archived

    Member
    October 24, 2020 at 1:49 pm in reply to: air ride system problems

    Thank you Mikee!

  • Archived

    Member
    October 24, 2020 at 11:20 am in reply to: air ride system problems

    Hello!!!

    I found the problem and it is now working properly in drive mode. After all the help from Jon and Don and few others I was convinced that the drive mode norgren valves were not opening as they should but not knowing the real reason why. I checked the number 3 coil out a couple of times thinking it was working and it had small amount air coming out of 3 that activates the drive mode valves but not near as much air as the 5 coil log had going in. So I removed #3 coil and valve and tore it apart to find a small piece of debris blocking most of the tiny center air passage. I cleaned it up and reinstalled and BA-BAM it worked and bus is sitting at 11” all four corners.

    Ok update lol the bus sits at 11” for 6 minutes not running and then air is dumped in the rear somewhere right a 6 minutes and the bus drops down 2” if the bus is running it stays up no problem. I engaged the tag lift while is was running and air is released somewhere around the tag and drops down a few inchs and the tag did not go up that i could see. Should the tag come off the completely off the ground when engaged and how far?

    Thank you all for your help!

  • Archived

    Member
    October 24, 2020 at 10:58 am in reply to: 02 H3 45 drivers power window problem

    Tom

    yes it is the toll window. Any help or direction would be appreciated. Hook me up! Thx

  • Archived

    Member
    October 23, 2020 at 5:35 pm in reply to: air ride system problems

    No, the 3 port/2 way Norgrens are on the inside of the frame above the tag axle.

    The 5 port/3way Norgrens are on the the bulkhead, forward of the drive axle.
    The bus will need to be raised and supported properly at the jack points.
    Safety first.
  • Archived

    Member
    October 23, 2020 at 4:52 pm in reply to: air ride system problems

    Thank you for all this great info! could i use shop air to test the see if more air would engage the rear valves?

  • Archived

    Member
    October 23, 2020 at 4:08 pm in reply to: 02 H3 45 drivers power window problem

    I just replaced the motor assembly. On the driver’s side it should be easy because you do not have all the trim and hidden fasteners to deal with.

    It was a Cardone 82-144. It was a drop in replacement.

    $170 from multiple sources.

  • Archived

    Member
    October 23, 2020 at 4:00 pm in reply to: 02 H3 45 drivers power window problem

    Jon

    love it. Jeff put in a new frig and a couple of new glasses. This is the small window on the drivers side. Did you just replace the motor or the motor/regulator assembly? Do you get to it from the cockpit or outside electrical panel? Thx

  • Archived

    Member
    October 23, 2020 at 3:28 pm in reply to: air ride system problems

    testing now with motor running in low level mode raised up to 11” front and back and has stayed there for 10 mins, switched to drive while running and no change so far in ride height

  • Archived

    Member
    October 23, 2020 at 3:07 pm in reply to: air ride system problems

    Pictured below is my bus level low “5 stack” setup. Yours may be different? Yours may be all 24v? But, you see how I have labeled their correct position in the stack and voltage?

    If someone working on it put a 24v coil where a 12v belongs it will act up intermittently. 12v going to a 24 v coil is not good. There should be a voltage label somewhere on each coil. Pull ea off and look them over. Get a multimeter out, activate ea coil with the level low switches and check to see that each coil is getting the correct voltage, 24v or 12v. This was the case with my bus when we first got it. Get a multimeter and check ea
    Also, if someone had the coils off the stack for whatever reason and put 1 or more back in the wrong position? this would not be good.
    Keep feeding us info, we haven’t spent any of your $ yet 🙂
  • Archived

    Member
    October 23, 2020 at 3:02 pm in reply to: 02 H3 45 drivers power window problem

    Jon

    is it hard to get to?

  • Archived

    Member
    October 23, 2020 at 2:59 pm in reply to: air ride system problems

    Getting closer.

    That is an unmodified level low unless a previous owner got creative. For the moment let’s assume nobody messed with it.

    If you raise the coach all the way up manually and then go to the road position what happens?

    If you lower the coach all the way down and go to the road position, what happens?

    If the answer in both cases is nothing, look in the steer compartment and look for a manifold with small diameter air hoses. It should have 5 valves in the manifold with red caps on them. The center solenoid valve coil has a high failure rate because it is always energized when driving.

    Put the coach up or down, and then switch the solenoid valve coil with ay other one in the stack. Do not reverse wires. let the go to the original positions. Just swap coils. Be careful you don’t drop and lose the “C” clip.

    If the coil has failed switching it with another should allow the coach to go to the correct driving height. If it does not we are out of low hanging fruit and now you are really going to get your hands dirty.

  • Archived

    Member
    October 23, 2020 at 2:46 pm in reply to: air ride system problems

    It is a Royale by Monaco conversion and in very original condition and looks to be not modified in anyway. Yes in low level all good both front and back. Drive mode front goes up and back does nothing, does not move at all.

  • Archived

    Member
    October 23, 2020 at 2:36 pm in reply to: air ride system problems

    Here is what Kirk originally wrote:

    “if i pump it it very high front and back the front stays put and the rear will set high for about 2 minutes and something dumps the air out and lowers down a couple inch’s but not completely empty and the bags still have air in them as i can see them through the dock light hole but the bus is sitting low.”
    It is my understanging that this is how a bus of Kirks vintage, 1995/6, with the original inverted tag bag logic would behave once the aux air system pressure dropped to about 30 psi. Granted, a healthy aux system should not leak down from 110 psi to 30 psi in 2 mins. 2 days would be great. Mine leaks down to zero in 24 hours. Remember, the tag bags are the only bags that get dumped when the aux pressure drops to 30 psi. You can’t see the tag bags thru the docking light hole.
    I’m still thinking about the other issue(s).
  • Archived

    Member
    October 23, 2020 at 11:19 am in reply to: Latest Used Oil Analysis
    I’m using Fleetguard filters # LF9620, has both a full-flow and by-pass section.
    Here’s a link about the technology: LINK
Page 109 of 2304