Forum Replies Created

Page 6 of 22
  • steve

    Member
    December 8, 2020 at 10:27 pm in reply to: Tag Air Release

    Thanks for the responses and I bet that is exactly what is happening. I have noticed the Aux system losing some air so it all now makes sense.

    I will take on the Aux leaks and maybe see what I can learn about the kits as well.

  • steve

    Member
    December 5, 2020 at 9:50 am in reply to: Front suspension flat

    Thanks Jon. I meant to change the coils! As long as the drive coil is working properly it’s safe to drive. Just a pain to level once parked until you get them all working!

  • steve

    Member
    December 2, 2020 at 5:29 pm in reply to: Not a happy wife, not a happy life

    Yes sir . I did the same thing at Prevost Nashville once.

  • steve

    Member
    December 2, 2020 at 8:25 am in reply to: Generator air bags/fittings.

    You could identify the leaking line/airbag by plugging off the other three and checking each line. I would soap up all the fittings and air bags.

  • steve

    Member
    November 19, 2020 at 10:42 pm in reply to: Changing hose in condenser compt to dash unit

    That bay looks really familiar, looking at the color and nap length it looks like a 1991 Beaver Prevost conversion. Dust level on the hose makes me believe its probably it might be conversion number 26 or 27.

  • steve

    Member
    November 17, 2020 at 9:38 pm in reply to: Volvo vs. Detroit RPM’s….

    Volvo electric fan upgrade must be Volvo 2010 or newer engine.

    Rake rate about 30k depending on rear door DS configuration.

    Later

    bv

  • steve

    Member
    October 29, 2020 at 7:45 pm in reply to: dealer review

    That is why I asked. Sometimes the internet has only negative post while the positive folks don’t post.

    Thanks!

  • steve

    Member
    October 7, 2020 at 7:11 am in reply to: Tom’s new ride

    Yes that’s me beside the pickup and travel trailer, you should have taken the picture from the other side trouble maker.

  • steve

    Member
    September 1, 2020 at 7:29 pm in reply to: Urgent Help needed, ride height issue

    If you hear the click, then crack the air line coming from the valve and make sure you hear air flow before going any further.

    And to be honest I keep forgetting there are other issues caused by poorly maintained air systems such as water in the system or sludge due to moisture preventing valves from shifting as required.

    When I have a system malfunct ( a highly technical term) I start at the beginning and follow air flow or current flow until I find the issue so rather than go beyond the manifold I first would verify it is infact allowing air to flow in the road position.

  • steve

    Member
    August 17, 2020 at 3:28 pm in reply to: Another Air Bag Question

    45 foot, 2005 chassis, XLII, 2 slides, 18,000# steer axle. I provided that because what might be acceptable for my coach might not work on others.

    Steer axle…….630239

    Drive axle…….630104

    Tag axle……….630151

    The air bags were not obtained without a great deal of difficulty. 2 of the three were wrong on the initial order, with all problems related to the size of the threaded air fitting not fitting in the hole in the top plate, or the orientation of the threaded studs, 90 degrees from where they should have been.

    The numbers above are what is now on the coach and they work.

  • steve

    Member
    July 30, 2020 at 1:25 pm in reply to: Belt Tensioner Issues

    Eliminated the tensioner, mini air bag years ago. Never had an issue since. Just install stainless bolt in it`s place , adjust tension, tighten an drive.

  • steve

    Member
    July 30, 2020 at 9:47 am in reply to: stainless latch?

    Doubles hold more.

  • steve

    Member
    July 29, 2020 at 11:19 pm in reply to: Are CruiseAirs Good Enough?

    Im not even CLOSE to hitting my head, Im 5’7″ standing up straight. When I was a kid I hated being small, now Im grateful! Last one is getting installed in the bedroom. Gonna be tricky because the mirrored ceiling is a circle directly over the bed, and there is a support brace there for the roof right in the middle. So ive got 2 options, cut out the sheet metal and the ducting should be able to go around the brace with it in place like a bare rib, or cut the brace and weld in a 14×14 square. Im hoping the first option works…

  • steve

    Member
    July 28, 2020 at 5:20 pm in reply to: Let’s Talk ISRI seat

    We bought parts for our ISRI 6500 from Tyler @ Darby Manufacturing Limited of Ontario Canada, 705-560-4663.

  • steve

    Member
    July 27, 2020 at 12:22 am in reply to: Tire Cupping

    One photo appears to show mudflap bracket that you see behind duals. So, im guessing the tire in question is a tag tire. Scrubbing around corners are brutal on tag tires. Appearance that the sidewall closest to tread edge has scuffed the pavement too. Air psi maybe matched to weight chart for michelin, but reduced air in the 80 psi range cause tag tire to literally lay over while turning. We run 100 on ours

Page 6 of 22