Archived
Forum Replies Created
-
That’s a lot of monkey F%#*g around.
Just wire a brake light switch off the pedal.
Later
bv
-
That’s the difference between a driver and a tourist on cruise control.
Later
bv
-
+1 on the Delco batteries. While I don’t have years and years of experience with them, they seem to hold up well. I replaced chassis batteries in May. The old set were dated 2012 (put in by the previous owner). Like Jon, I will replace on a 5 year or so schedule.
-
Cold temperature charging of Li batteries is restricted to a percentage of the battery capacity.
I am using heat to compensate for a brain fart. My fear is accidently starting the coach with cold batteries and having the coach alternator (50DN, 24V, 270 amp) slam a lot of charging current into cold batteries.
-
Thanks Jon, yes I’m aware of the various limits of Lithium batts. I’ve been doing a lot of homework.
I will be fully enclosing the battery area even though we live in TX. During a typical winter here it may get a few degrees below freezing for a few hours a few times/yr. Regardless, I’ll be prepared for another polar vortex like we had last Feb. I’ll be installing a small 12v 12w heating mat on/under each battery that will be automatically controlled by a capillary tube type thermostat and switch. At least that’s the current plan, subject to change at any time. 🙂 -
Dick-
I have no experience with the NAPA group 31 batteries, I was just going by what seems to be a very positive opinion here on the forum. I’m thinking this may just be a bad batch. As I said, they are all dated coded 12/21. Bay area CA.
I’m not sure of the age of the chassis batteries, they were in the bus when I bought it. The only code I see on the battery is OJKD13. I would find it hard to believe they were from 2013.
-
Jon: Is the cold weather issue with Lithium batteries that they WON’T accept a charge if below 32*F? Or that they should NOT be charged if below 32*F (under the premise that Lithium batteries can be damaged when charged at temps below 32*F)?
This probably isn’t a good comparison … but … I have an extensive set of Craftsman C3 19.2 volt cordless tools that originally came with Ni-Cad batteries which have been replaced with C3 19.2 volt Li-Ion batteries. A couple of weeks ago I left a tool and two batteries in the car outside on a cold night (in the 20’s). The next morning I needed the tool, brought it and the batteries in the house, dropped the batteries into the multi-chemistry charger, and immediately got the “bad battery” indication for both of them. I knew they were good and presumed they were too cold. So I unplugged the charger and an hour later I plugged it in and both batteries accepted charging.
Now I don’t know if the charger sensed battery temp and refused to charge them because of their low temp, or if the batteries knew their temps and refused to accept a charge which caused the charger to see a “fault” and gave the “bad battery” indication.
-
Archived
MemberDecember 15, 2021 at 4:54 pm in reply to: Recent experience with Ft Worth Prevost Service ?Well— I had them check out my brakes. The front brake acted like it was bone on bone. They said it was within their specs. Never had a coach act like that. Never had any other prevost act like that. I just gave up.
the straw that broke- I had a coolant leak above the drive axle. They said it would cost 5 grand to replace those lines. My son and I did it in 30 minutes with 4 bucks worth of hose.
caveat emptor
-
“Diesel” generators are exempt, which means diesel generators in Prevost motorhomes as well as large Class A diesel powered coaches are “exempt”!!! More information can be found here. The talk of “credits” base upon approved power-generating alternatives per SORE can defer banned until 2032 on LP/gasoline sparked engines less than 25hp
https://rvbusiness.com/calif-concedes-generator-ban-creates-woes-for-rv-industry/
RVBusiness.com Dec14, 2021
-
When you open the home page click on where it ask for the password. Mine will ask to give you a password then make sure you move the mouse 90 degrees to the right then down to where it says don’t use. Click there then when you go back to password click and it will show all the passwords you have tried to use. Click on the one you want and it is put in place. When the home page opens again click on forums.
-
David has an amazing skill set and is always ready to help.
-
Bruce, that is quirk of Safari. Use Firefox and the info will be saved.
-
“How would M&G system solve Lardogs problem?”
Hey Larry, you took the words right out of my mouth brother. Oh BTW, it was nice meeting you up at Marathon. Sorry we didn’t have more hang time to get to know each other better.After trying to figure out what Jon and Tom were goading each other about and checking the internet to see if I just wasn’t hip enough to get the G.O.A.T., reference I finally gave up and just figured ehh…it’s and inside thing.
Would I have preferred an air actuated braking system like the Air Force or M&G since from what I’ve read they seem to be the best options? Absolutely! But I needed to outfit the car with a tow package and braking system 2000 miles away from where I was picking up the coach. Since the previous owner said the coach didn’t have an air chuck in the rear for the toad braking I opted for the InvisiBrake system from Roadmaster and had the entire tow package installed by Camping World before we set off to get the coach. I wanted to make sure I had SOMETHING in the toad in case I got stopped in a state that requires it.
At this point I’m leaning towards Toms suggestion to crack open that box in the engine bay where all the tow wiring seems to terminate. I spoke to Marathon and they said It’s possible some moisture may have infiltrated that box so I really want to peek inside there and see what’s what. All three screws were rusted so a little Blaster penetrating lube help me get two of the screws out but it looks like some neanderthal cross threaded the third and it won’t budge, so I have to wait till I have the time to cut the head off that other screw to open Pandoras box.I’ll report back with some pics once I have a look see inside and give you guys an update if I figure out the problem I’m having.As always, thanks for all the input. You never know when you’re going to read the post that says BINGO!!!…that’s it!!…problem solved! -
Hey Jon good answer I willcheck it out Thanks’
-
Fred to loosen hold 90 degree fitting and loosen nut that is threaded to the 90 ,the nut on top will swivel ,the fitting below 90 is all one piece.