Forum Replies Created

Page 2277 of 2304
  • Archived

    Member
    February 21, 2012 at 4:58 am in reply to: Air leak repair

    Third leak is the left air gauge in the dash. It is leaking out of the push connector on the back of the gauge. I tried getting the 1/8″ hose out of the coupler to no avail. Tried pushing in on the release and pushing and pulling on the hose but it just would not come out. I will next get a new push lock and replace it on the back of the guage and the should fix that one.

    …………………………………………………………..

    My first adventure of chasing air leaks in my bus lead me to the same leak you are describing. The fittings used to connect the 1/8″ tubing to the Primary and Secondary pressure gauges are ‘low hanging fruit” in the pursuit of managing bus air leaks. The easiest thing to do is replace both of the the 1/8″ fittings. I searched for 1/8″ compression fittings to no avail, so I replaced the fittings in kind with new push to fit fittings. The new fittings rubber seals and the1/8″ tubing worked fine. I cut off an inch of the old 1/8″ tubing to expose uncompressed tubing and reinstalled.

    I am the guy that had soo many leaks on my bus when purchased, I had to become very aggressive to manage these leaks. I 1995 Prevost will sit for weeks and will not lean. The aux air compressor will run every couple of weeks. It will take effort to achieve this level of air tightness, but it is doable.

    My last comment on leaks. For me, leaks have been a moving target. Meaning, getting a bus to a leak free status once does not mean it will stay leak free forever. You will need to monitor and manage leaks. Their are soo many opportunities for leaks in our complicated suspension systems.

    Good Luck,

    Hector

  • Archived

    Member
    February 20, 2012 at 9:07 pm in reply to: New Tires ok New Air?

    Roger,

    What is the increased value you mentioned?

  • Archived

    Member
    February 20, 2012 at 3:09 pm in reply to: Air leak repair

    Thanks Jon. I thought it best to start with the obvious. I agree it will take a lot of work to get it leak free, but I enjoy that type of investigative work. I am off to search for parts!!!!

    Thanks,

  • Archived

    Member
    February 20, 2012 at 1:34 pm in reply to: RV PARK POWER SUPPLY TESTER

    I cannot remember the last time I only had 30 amp power available. If I cannot get a campground with 50 amps I just dry camp and run the generator. I guess that makes me an energy snob.

  • Archived

    Member
    February 20, 2012 at 12:52 pm in reply to: RV PARK POWER SUPPLY TESTER

    So what do you use for polarity checking/surge protection on 30 amp hookups.?

    I’ve never had an issue until my last trip into an OLD park with 30 only and I had a couple screwy things happen.

  • Archived

    Member
    February 20, 2012 at 12:46 pm in reply to: RV PARK POWER SUPPLY TESTER

    Pure conjecture…………I would assume the surge protector functions as a protector based on the power into it, and not how the power is drawn downstream. Good question for the manufacturer.

  • Archived

    Member
    February 20, 2012 at 10:07 am in reply to: RV PARK POWER SUPPLY TESTER

    I’ve ordered one. Question: Will this also function as a check/surge protector on 30 amp hookups if I come from the pedestal with a male 30 to female 50 into this unit?

  • Archived

    Member
    February 20, 2012 at 8:55 am in reply to: RV PARK POWER SUPPLY TESTER

    Some coaches trip GFCI receptacles, some will not. It depends on how the converter handles the connection to shore power and establishes a ground connection prior to the transfer switch letting shore power into the bus.

    The surge protector has no affect.

  • Archived

    Member
    February 20, 2012 at 7:28 am in reply to: Roof Air Replacement

    Sounds like that’s the way to go, heat strips instead of the heat pump.

    Thanks…

  • Archived

    Member
    February 19, 2012 at 7:51 pm in reply to: Roof Air Replacement

    Tom: Just another opinion here, but I have experience. I would recommend when replacing the heat pump/Roof Air combo unit to consider going with the heat strip vs the heat pump. I had my old ones replaced in 2010 and it seems the noise level produced by the newer heat pumps is about 30 percent higher than the ones I replaced.

    At least the heat strips are silent and the only noise will be the fans.

  • Archived

    Member
    February 19, 2012 at 6:51 am in reply to: RV PARK POWER SUPPLY TESTER

    I use the same surge protector that Jon has and it’s worked well for many years. Seems like the guys that bought the more expensive version with digital displays have had a bunch of problems and some are on their 2nd and 3rd replacement.

  • Archived

    Member
    February 18, 2012 at 3:05 pm in reply to: RV PARK POWER SUPPLY TESTER

    http://tweetys.com/50-amp-portable-surge-protector-polarity-tester.aspx

    This is the surge protector I use and before I plug my power cord in I plug this in. If the 4 lights are lit all is well. If not it shows the problem. Word of caution…….the lights are hard to see in bright sunlight.

  • Archived

    Member
    February 18, 2012 at 7:00 am in reply to: Bar Door Gas Cylinders

    Hi Rob

    Great idea. Harbor Freight here i come. Sure sounds easier then I had envisioned.

    Thanks

    Terry

  • Archived

    Member
    February 17, 2012 at 10:08 pm in reply to: Posting With a Mac

    I am running Lion 10.7.3 with no issues.

  • Archived

    Member
    February 17, 2012 at 6:31 pm in reply to: Bar Door Gas Cylinders

    Hey Guys

    There is a very simple way to do it. Measure the length of the strut when fully extended. Once you have that number, say 24″, the go by your nearest Harbor Freight store and pick up a bar clamp that is slightly longer than the length of the strut. Now all you have to do is put the clamp on the strut, screw the clamp shut a few turns and install the strut. When looking at the bar clamps there are two types. Those that have a 3-4″ standoff and small point and those with a wide, no stndoff point. I would try the small point and place it on the strut at a right angle to the installation. Either clamp will only be $5-10 max. Some lumber yards or other woodworker places have the clamps as well. The other option, is to take some strong wire, about 16 guage and wrap it from one end around the other and then tie it off on one of the existing struts already istalled on the coach. Now untie it to remove it and once removed, retie it in the same spot. That is now the wire you use to tie the new struts so they don’t go beyond the right length when released.

    Wish I had a working camera as I would demo what I have written but the camera is not working right now. If you cannot figure out what I am saying, let me know and I will see what I can do about posting a pic.

    Rob

    91 XL40

    Missouri

Page 2277 of 2304