Archived
Forum Replies Created
-
Thanks guys, we’re not going anywhere, just two grumpy ole men glad to have some younger folks take the PC reins and make it grow. Bill and Jessica have some good ideas in store. Bill has been a Prevost owner for a long time.
Now I don’t have to listen to the whining from Knoxville about dues money, but the behind the scenes harassment is never ending.
-
Ron-
Same here. I run “noscript” on my browser, and had to ok a “poogle” script, then the error code went away.
-
I was getting the same every time I tried to access the “Coaches for Sale”. Most of the time the web browser needs to be restarted. However, after doing this may, many times, and restarting the laptop, the error continues.
R
-
NEARING THE END……..
We are here at etrailer and the process has begun. The Jeep is in the shop and etrailer is not more fully aware of the death wobble issues and with information from my paperwork may write and article to include on their site. They have had extensive experience with the wobble on Cherokees and are now aware of the issue following over to the Grand Cherokee.
The work I have seen so far is very encuraging because they leave no detail to chance. While the Jeep is in the shop for the base plate, wiring, and Brakemaster kits to be installed the bus connections were checked in detail to insure when everything is hooked up it will all work.
The plan is when the Jeep is done (which includes extensive video taping) then the Jeep will be connected to the bus, involving extensive testing of all the work from lights to brakes to tow bar and will include some parking lot driving as well as more video taping.
More reports coming.
-
Thanks Al.
To add to my comments above, If there is runout but the tire is showing equal spacing around the bead Al shows it can also be attributed to how the wheel is mounted on the coach. Put the greatest amount of runout at the top by rotating the tire. Loosen all the lug nuts to allow the wheel to drop a miniscule amount and retighten the nuts to spec.
Remeasure runout and it is likely much less than previous.
A high quality tire shop will always mount and seat the bead on tires when they are horizontal, often with the wheel sitting on a pail or 5 gallon bucket. That allows the tire to seat evenly. A good shop will also consider runout because balancing will only mask temporarily the problem. There is a whole lot more to tires than that they are black, round and hold air.
-
Jon-
Sounds good to me. I will reach out to him.
Thanks!
-
On 365 wheels the short stem will work perfectly if the valve stem is centered. The PP sensor will thread on the stem, not bind as it enters the relief hole and a shorter stem helps protect the sensor and keep the sensor from sticking out.
the key is the stem cannot be bent or off center.
-
I’ll make this real simple using an assumption. I assume your existing batteries while six volt are wired in series so you are set up with a 12V system.
Stick with 12V batteries.
Do not waste your time or money thinking you can save a few bucks on batteries. Contact Tom (Truk) who sells Lifeline. They are by far the batteries most of us use because of their performance. Give him the information he needs and he will set you up with the batteries that in the end, if taken care of are going to give you the biggest bang for your buck.
-
Dennis, Did you install the Furrion cameras? I am thinking of the same and like you am looking for any experience on the Prevost.
-
It absolutely positively has to be a Liberty, no doubt, cannot be wrong, it was on POG Fakebook.
-
I’m not sure you have that option. Vantare runs almost if not everything through inverters, and Parliament may also do that. Other converter run shore and generator power to the 120V AC distribution panel which feeds power to inverters. Inverters then take that power, or power they create from battery power to feed dedicated bus bars that have things such as the refrigerator, outlets, microwave, etc.
If Parliament is set up like Vantare to change and do what you intend may be pricey.
-
That is what I don’t like at the moment our inverter makes power for ,refrigerator, tv microwave, outlets bath and bedroom, salon ,I want shore power for power and inverter for backup.
-
And Jimmie and I are both right.
-
I am not sure I could find the wiring diagram I created to make an inverter by-pass, but essentially what I did was use a switch that sent power from shore or generator power to the inverter in one position to send it directly to the electrical panel in the other position. I used 30 amp switches because the power to the inverter was through a 30 amp breaker.
-
My friend neighbor has the truck center that is going to charge it I will supply compressor-oil-dryer, so if you don’t know how much 134a goes in you go off PSI? Doesn’t Prevost install the dash air?