Archived
Forum Replies Created
-
thanks. i am starting to think that a saws all is the bus owners best friend
petar
-
I would never service that part due to risk. And it is not worth the risk…period. Take Jons advice on the Prevost parts replacement and while your at it do the other side at the same time.
Both likely have been in the same amount of use..
AL
-
been awhile; phillips head screws in sides some hidden under plastic trim I think. Just tie into it. Saw -all is your best friend. The aluminum heavy mounting plate along wall comes out seperate to the best of my memeory. Lots $$ in alum scrap. good luck Bob
-
Not sure I completely agree with Jim. If this was a combo such as the service and emergency brake combined I would never consider repairing or servicing it due to the potential energy in the emergency brake spring.
However the lift chamber for the tag axle is a single service brake chamber, and while it has a spring inside, the spring is relatively light only serving to retract the plunger. The two halves of the chamber, with the diaphragm held between the two halves can usually be held together with one hand while the outer band clamps are put in place with the other hand. As to the cost however. definitely determine the generic size which will be a 30 or more likely a 36. A 30 is cheap, sometimes on sale at truck parts stores, sold out of a large bin for as little as $30. The 36 size is less common, but still relatively inexpensive. If the choice is to replace the diaphragm (looks like a black rubber cereal bowl) most are available for under $10.
-
You are but I’m not. I’m looking for an area campground that’s close and has 50 amps. Just wondered if anyone knew of another place to camp out.
-
I started the bus and checked for the leak today. The rush of air is definitely on the drivers side of the bus. This is a picture of the canister that is hooked to the chain that lifts the tag.
I sprayed it with soapy water and had my wife flip the lever inside and you can see it is leaking some in two places.
However, I could not feel any big rush of air escaping when I had my hand in there. Of course I could not leave my hand in there for long because the bus is coming down. I did try it several times in different places around that canister but I could feel no air with my hand. The canister is obviously leaking some but I do not think it is the main culprit.
Does this mean the air escaping is more likely coming from the norgren valve underneath the bus.
If the valve is exhausting with the tag lift engaged but at no other time I should be OK to drive it, correct?
Do truck shops work on these valves?
Thanks,
DKO
-
Wow, thanks to Prevost Community. This will come in very handy for touring. Yes this is a great site; happy to be able to participate.
-
Just off of I75 in Wildwood , Florida on Hwy 44 there is a little polish shop that i have been useing for years ,It is called < A Cut Above > I had my wheels done there about three weeks ago for $800 they came out perfect . The man polishing was boiling down a bar of polishing rouge, brown in color in mineral spirits he puts this mixture with a little carnuba wax in a squirt bottle and this is what he used with a buffer wheel, than a towel great job . Mine is a 1994 xl the headlights were a bit dingy also and twenty bucks they were shiney new also. I asked about the stainless ,, was told hand polish $3000 and for $6000 sand polish and wax with machine,, well now it looks like even better than new. I don’t know thier exact address and it is outside across from a truck stop nothing fancy just a great honest job. I got the machine job too about 6 hours but looks like new or beter he made sure all scratches were gone …
-
Congratulations on the fantastic growth of Prevost Community!
Looks like the future is very bright for this forum…..
Keep up the great work!
-
DKO,
If you look above the tag tire, about the 11:00 position, you can see the lift can. If it’s leaking, very easy to hear the leak or you can spray it with soapy water. The 3 ports are mounted high above the frame and can’t be seen unless you’re under the bus.
-
DKO,
The lifting device for the tag is visible behind and above the tag wheel. It lifts the axle via a short length of chain. The device is nothing more than a brake chamber. I can’t remember if it is a 30 or 36 chamber, but if that is the leak the chamber is available at any truck parts store for $35 or $40 or you can repair it by buying the rubber diaphragm for about 25% or less of the cost of a new one.
And Gh is right. if it is the three port norgren(s) and it fails to completely shift the spool it will also exhaust air, more than just that in the tag air bag..
-
Scott,
If your talking about the rally, we are signed up for 50 amp in the campground at the rally location.
-
There are two schools of thought on the suspensions and their parts.
I fall into the first which is to decide when they have outlived their usefullness and just replace them. I picked 10 years as the age I will replace or rebuild the Norgren valves and replace the air bags. I end up throwing away a lot of perfectly good parts but I rarely have to deal with the leans or problems associated with an aging suspension.
The second option is to leave well enough alone and just replace things when needed. There is certainly some wisdom in that approach because sometimes replacing parts which work properly leads to chasing leaks which did not exist before. I doubt if a motorhome conversion owner can make a choice as to which approach is better because we don’t have fleet statistics available to us to use so we can base a choice on data like a seated coach operator might have. Adding to the difficulty is we often cannot determine if our limited use of our coaches contributes to the longevity of the parts or is adversely affecting them. I suspect inactivity is not good for Norgren valves, but have no data to prove that
So the bottom line is we each have to decide how we are going to deal with our suspensions and their parts. Do we accept the fact air bags are age limited and replace them, or are we comfortable waiting until we get the leans or worse, have an air bag fail. One thing is for sure. At some point our air bags will leak or burst. We just don’t know when.
-
Norgren solenoid Valves: The right rear was giving me trouble after being parked it would not join the rest of the valves by coming up to the travel setting position. I worked the right rear high / low switch with the travel swith in the center position several times finally coaxing it to finally come up to the travel position. I disasembled the guilty solenoid and cleaned and re-assembled it and so far so good. I’m thinking after 12 years use it’s time to order a new set of Norgren solenoid valves and all other Norgren valves to have on hand. I’m still on original air bags and knock on wood no problems with them. Any suggestions on these items would be apreciated.