Prevost Community Forums

Find answers, ask questions, and connect with our
Prevost Community around the world.

  • WATTS Pressure Regulator Specs?

    Posted by Chas on October 29, 2014 at 9:48 am

    Trying to determine what the specs are on the WATTS H560 Pressure Regulator used on the water fill/city water line. See attached pic of the pressure valve.

    When I look up the part on WATTS website, it shows the H560 with a dial gauge and hose connectors.

    From what I can tell, I should be looking for a 560 with 1/8″ inlet/outlet and 0-60 PSI (this is showing as LF560 as the 560 has been discontinued).

    Do these specs sound correct?

    AL replied 11 years, 11 months ago 6 Members · 12 Replies
  • 12 Replies
  • Dick

    Member
    October 29, 2014 at 3:11 pm

    Charles,

    I used an LF560 and also removed that plastic restrictor. LF560

    When I removed the plastic restrictor, I found it full of teflon tape. This picture is looking down into the removed restrictor showing the tape.

  • Dick

    Member
    October 29, 2014 at 4:25 pm

    Tom, do you recall if you got the 1/8 or 1/4 inch inlet/outlet? I am assuming it will use the 0-60 PSI and not the higher pressure 0-125 regulator.

    Liberty is saying to get a solid inline pressure regulator, but I couldnt find one at the RV Store, all they had were the ones you attach on the end of the hose that attaches to the fill line. Would rather have something like what is there to make it more consistant. Of course that would mean there is still possibility of leak down the road. I guess replacing from the while coupler above the reg down to the grey T adapter with pipe and using the external regulator woudl reduce that potential issue?

  • Archived

    Member
    October 29, 2014 at 5:46 pm

    Charles, I will address this knowing you have a Liberty.

    First, your coach operates best when you use the water pump exclusively. It is set up so you have ample pressure and volume at all times, whereas on city water you have no assurance you will have both at all times. That lack of consistency can make things not work properly such as low pressure or volume affects the toilet, and too much can affect everything else.

    You do not need protection against unusually high pressures from a regulator if you do choose to let your pump do what it is supposed to do.

    Here is what I have done. I hook up city water but do not open the flow. I have my supply hose set up with a valve at the coach end. I open the water inlet ball valve, I open the tank fill by pressing the switch, and only then do I open the flow from city water supply. When the tankis full I reverse the steps. I know I am not using the auto fill feature by doing this, but there is a reason for my choice. First, I never fill unless I empty the holding tank. That minimizes the possibility of an over flow. Then I only fill the water tank to a percent of its volume that equals the holding tank volume. That also minimizes the possibility of a holding tank overflow. And lastly my water system never sees pressures that could be unsafe whether the regulator works or not because I am never allowing city pressure into my coach system.

    The regulator is a restrictor so if you do remove it you will fill you tank faster.

    This was all learned about 23 years ago at a RV park in Salt Lake City that had so much pressure that it would open the pressure / temperature relief valve on the HW tank.

  • glen

    Member
    October 29, 2014 at 6:58 pm

    jon,

    i actually only use the hookup to fill and never as actual water.

    with that in mind, i should be okay to remove the regulator and carry an adapter regulator if ever needed?

  • Archived

    Member
    October 30, 2014 at 6:34 am

    Yes. The regulator is there to protect against the unusual high pressure conditions, but if you open the ball valve, tank fill valve and then the water flow from city water to the coach in that order your coach system will never be exposed to excessive pressures.

    On our Liberty coaches I think the system is capable of handling very high pressures, but the limitation is the 75 PSI valves on the HW tank.

  • Archived

    Member
    October 30, 2014 at 9:46 pm

    I see the problem with people’s hose bursting from being left on in the campgrounds, not with the coaches systems.

  • Archived

    Member
    November 30, 2014 at 3:34 pm

    completed the plumbing fix. Seems the plastic “restrictor” is really a back flow valve and is needs ( the hour glass shaped part below the pressure regulator).

    here is the end product. Have a pressure regulator on the hose now.

  • Larry & Diane

    Member
    November 30, 2014 at 3:35 pm

  • Chas

    Member
    November 30, 2014 at 5:55 pm

    Charles,

    Are you saying the white restrictor is a back flow preventer and if so, where did that info come from?

  • Chas

    Member
    November 30, 2014 at 6:09 pm

    that info came from water shooting out of the hose when i opened the blue valve at the bottom, and turned the switch to fill. and confirmed when i took that part off and looked inside and noticed a one way spring valve inside it 🙂

  • AL

    Member
    November 30, 2014 at 9:06 pm

    OK, when I removed mine I put a check valve inline.

  • Archived

    Member
    November 30, 2014 at 10:26 pm

    in the end it only meant another trip tp true value. and when im working in my shorts and a tshirt, i cant complain 🙂

    no leaks, and fill works as expected. since i only fill and never use “city water”?

Log in to reply.