Prevost Community Forums

Find answers, ask questions, and connect with our
Prevost Community around the world.

  • H LED Post Transfer

    Posted by Archived on November 6, 2014 at 9:47 pm

    11/4/2014 7:59:06 AM Truk4u

    Thanks Jerry… Al just tried those form IBP and had to send them back, maybe you go the good ones.:)

    His post is here H LED’s

    Tom & Nancy
    02 Marathon H, 732
    08 Jeep Wrangler

    Reply
    11/4/2014 8:35:01 PM jbchevy3

    Tom, I haven’t had any problems with mine. I’ll check the brand/part number. Maybe they are different from Al’s.

    Jerry & Gayle
    01 H3 45 DBL Slide, OTR, Vantare
    13 F150 FX4 Ecoboost
    Featherlite Stacker

    Reply
    11/6/2014 12:40:42 PM jbchevy3

    Tom, they are Dialight Series 84. I have had no problems.

    Jerry & Gayle
    01 H3 45 DBL Slide, OTR, Vantare
    13 F150 FX4 Ecoboost
    Featherlite Stacker

    Reply
    11/6/2014 8:55:26 PM Dick in Wisconsin

    Looks nice! Do the same lights fit on an XLV?

    We could probably use a Form topic dedicated to LED lighting!

    Dick Karth & Cathie Sunday
    1998 Prevost XLV
    1999 Liberty Elegant Lady #407
    Grafton, Wisconsin

    Reply
    11/6/2014 9:36:51 PM Truk4u

    Thanks Jerry..

    After several calls to Dialight and a few of their distributors, you end up at Prevost. Couldn’t come up with any other source.

    Sorry for the thread creep.

    Chas replied 12 years ago 2 Members · 2 Replies
  • 2 Replies
  • Archived

    Member
    November 6, 2014 at 11:20 pm

    Trying very hard to find LED tail lights. The one from Prevost will not work. Even if I trim the plastic we’re still have the aluminum mount bracket in the way.

    So my question is where is your LED source ? The pictures look like Prevost sent me …that were supposedly ready to bolt in replacement.

    Unless I Dramel grind the engine bay door Prevost will not mount flush.

    IBP has contacted me today. Discussion on the mounting issues with there LED lights. They are willing to use my suggestions with detailing the LED assembly. This includes;

    Either electric weld the mount stud complete or better relocate the stud through the back side of the support plate with a weld the prevent the stud getting loose or breaking during install.

    Move the studs an additional 1/32 inch further apart…this eliminates enlarging the holes in engine door.

    IBP has lazer cut an attractive bezel. The cut is very sharp on outer edges should be slightly polished to remove a razor sharp outer edge.

    Back side of Prevost taillight. Base ridge and mount bracket about 1/8 in from edge prevents flush mount.

    IBP uses a slightly smaller LED then custom makes bracket along with studs welded to plate. LED includes wire assembly to plug into existing Prevost plug in.

    Polished stainless bezel

    17 lights are mounted on rear bay door

  • Chas

    Member
    November 7, 2014 at 9:24 am

    Another transfer..

    11/7/2014 8:20:43 AM SEABYRD

    Al,

    Those IBP are the exact ones we had and they looked great and were a good fit, we did have one come apart from the light itself and I reattached it with epoxy… we were lucky we didn’t lose the light as it was hanging by the plug in wire and the SS Bezel was still there… if you do go this route be sure and use some good industrial 3M two sided tape under the edge of the Bezels…it will stop them from shifting and don’t overtighten the nuts on the lights or they will separate too.

    Good luck, Diane

    Larry & Diane Byrd, Lufkin, Texas.
    2005 Liberty Elegant Lady H3-45.
    2015 Suburban 4WD LTZ

    Reply

Log in to reply.